Ford Falcon. Manual — part 379
417-01-55 Exterior
Lighting 417-01-55
REMOVAL AND INSTALLATION (Continued)
Tail Lamp Assembly — Wagon
Tail Lamp, Reverse Lamp and Rear
Indicator Bulb — Sedan And Wagon
Removal
1. Open the liftgate.
Removal
1. Follow steps 1, 4, 5 of Tail Lamp Assembly
Removal and Installation procedure, so that lamp
assembly is free from vehicle. It is not necessary
to disconnect the electrical wiring from vehicle.
2. Remove the rear quarter interior trim.
3. Disconnect wiring connector to tail lamp and
squeeze rubber grommet through hole.
4. Remove the two retained screws, one on the
2. Remove bulb holder from socket by rotating
inboard side and another one on the top of the tail
holder anti-clockwise approximately 1/8th turn
lamp assembly.
until free from socket.
5. Insert a thin flat head screwdriver or similar object
Stop and tail lamp - (clear twin filaments bulb)
having a flat blade to the forward side of the
outboard stud and gently prise it off the plastic
Indicator lamp - (amber bulb)
retainer, being careful to protect any paint from
Reverse lamp - (clear bulb)
damage.
3. Remove bulb from holder by rotating
6. Remove the tail lamp assembly.
anti-clockwise approximately 1/8th turn.
Installation
Installation
1. Pull the wiring assembly in and ensure the rubber 1. Install bulb in holder by gently pushing bulb into
grommet is correctly seated to body panel.
holder and rotating bulb clockwise.
2. Insert the locating peg to the upper inboard
2. Insert bulb and holder assembly into socket. Note:
square hole on the body panel and push the
the holder cannot be inserted into the incorrect
outboard stud into the plastic retainer.
socket. Rotate holder clockwise until firm in
3. Install the two retained screws.
socket.
4. Connect the wiring connector and refit the rear
3. Follow the procedure given in this section for
quarter interior trim.
installation of the tail lamp assembly.
5. Close
the
liftgate.
Tail Lamp Assembly — Style Side Box
Removal
1. Open
tailgate.
2. Remove two bolts on taillight edge.
G86747 en
417-01-56 Exterior
Lighting 417-01-56
REMOVAL AND INSTALLATION (Continued)
3. Remove lamp, pulling away at 45 degrees.
2. Carefully insert the tail lamp assembly, snapping
the two retaining tabs into place.
3. Install the two bolts.
Reverse Light Replacement — Style
Side Box
Removal
1. Remove the two bolts attaching the reverse light.
Item
Description
1
Bolt (x2)
2
Tail lamp wiring
3
Tail lamp pin location guide
4
Tail lamp assembly
4. Disconnect
wiring.
Installation
Item
Description
1. Reverse removal procedure.
1
Reverse lamp
Rear Light Bulbs Replacement — Style
2. Carefully insert a flat blade under the lens.
Side Box
3. Disconnect the bulb connector.
4. Remove the bulb to be replaced.
Removal
Installation
1. Remove the two bolts from the inside of the
tailgate.
1. Insert a new bulb and replace the wiring
connector.
2. Carefully pull the tail lamp assembly from the
liftgate pillar by releasing the two retaining tabs.
2. Replace the lens and install the two bolts.
Tail Lamp Assembly — Tray
Removal
1. Remove M6 nuts from lamp mounting bracket.
Item
Description
1
Brake/Tail lamp
2
Indicator lamp
3. Disconnect the wiring connector.
Item
Description
4. Carefully pull out the bulb to be replaced.
1
Tail lamp assembly
Installation
2
Nut - M6
1. Insert the new bulb and replace the wiring
connector.
G86747 en
417-01-57 Exterior
Lighting 417-01-57
REMOVAL AND INSTALLATION (Continued)
Rear Light Bulbs Replacement —
Cable/Chassis and Tray
Removal
1. Release the retaining clip and swivel aside the
plastic frame that secures the lens.
Item
Description
1
Reversing lamp
2
Indicator lamp
3
Tail lamp
4
Brake lamp
2. Remove the lens from the lamp assembly.
3. Remove the blown bulb by gently pressing the
bulb down and turning it anti-clockwise.
Item
Description
Installation
1
Bolt
1. Insert a new bulb, replace the lens and close the
2
Nut - M6
plastic frame with the retaining clip.
3
Tail lamp assembly
Licence Plate Lamp Assembly
4
Ute chassis
5
Mointing bracket
Removal
1. Gently insert a flat blade or similar object under
Installation
one side of lamp assembly and gently press on
1. Reverse the removal procedure.
the locking tab.
2. Lift the lamp assembly out of the bumper or
applique.
3. Disconnect the wiring connector.
G86752 en
417-01-58 Exterior
Lighting 417-01-58
REMOVAL AND INSTALLATION (Continued)
Installation
Rear Licence Plate Lamp Replacement
1. Connect the wiring connector.
— Chassis/Cab and Tray
2. Position lamp assembly and push into bumper or
Removal and Installation
applique until locking tabs engage.
1. Push off the rubber band and pull off the cap.
Licence Plate Bulb
Removal
1. Remove lamp assembly as above leaving the
wiring connected.
2. Turn bulb holder approximately 1/8th turn
anti-clockwise until it is free.
3. Pull bulb out from socket.
Installation
NOTE: Tabs prevent the bulb holder from being
inserted into the lamp assembly at the incorrect
orientation. Do not apply force.
1. Reverse the removal procedure.
Item
Description
Rear Licence Plate Lamp Replacement
1
Retaining bolt
— Style Side Box
2
Licence plate housing
Removal and Installation
2. Remove the bulb by gently pressing it down and
1. Carefully insert a flat blade under one side of the
turning it anti-clockwise.
lamp assembly. Press gently on the locking tab.
3. Insert a new bulb and replace the cap in the
rubber band.
Side Indicator Lamps
Removal
1. Turn front wheel outward.
2. Remove front splash shield fixings behind wheel,
and peel splash shield back.
2. Lift the lamp assembly out of the bumper.
3. Disconnect the wiring connector.
4. Turn the bulb holder approximately 1/8th turn
anti-clockwise until it is free. Pull the bulb from the
socket.
5. Replace the bulb and bulb holder, connect the
wiring connector and push the lamp assembly into
the bumper until the locking tabs engage.
Item
Description
1
Fender splash shield
2
Firtree Cip - 6.5x25mm (x2)
3
Scrivets - 6mm (x10)
4
Screw - 5mm (x1)
5
Screw - 5mm (x2)
G86752 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст