Ford Falcon. Manual — part 332
413-01-11 Instrument
Cluster 413-01-11
DIAGNOSIS AND TESTING (Continued)
Input and Data Test
This test will check for hard wired inputs to the cluster
1. User will be prompted with items to check and
data to verify
1.
Park
Lights
2.
Park
Brake
3. Left Turn / Right Turn Switch
4.
Autolamps
2. Tests on input status will be conducted, with user
confirmation. Upon failure detected user will be
guided through further tests for that particular
failure.
This test will also check for data errors (Odometer,
Trip data, etc.)
3. User will be prompted with item to check,
verification of data and further tests to conduct will
be provided as required.
DTC Chart
Instrument Cluster Diagnostic Trouble Code (DTC) Index
Display
Description
Action
B1201
Fuel Sender Circuit Failure
Conduct Functional Test: Gauge Test
Conduct Pinpoint Test: ‘Fuel Gauge Circuit Test’
B1342
ECU is faulted / EE checksum
Internal data failure, disconnect power, wait 10
failure
seconds and re-apply power. Run self test. If DTC
is still present, Conduct Functional Test: Data
Test.
B1499
Lamp Turn Signal Left Circuit
Bulb out detected on Left Turn Circuit. Check
Failure
bulbs, then conduct Functional Test: Input and
Data Test.
Conduct Pinpoint Test: ‘Turn Signal Input Test’
B1503
Lamp Turn Signal Right Circuit
Bulb out detected on Left Turn Circuit. Check
Failure
bulbs, then conduct Functional Test: Input and
Data Test.
Conduct Pinpoint Test: ‘Turn Signal Input Test’
B1579
Dim Panel Increase Input Circuit
Dim Increase circuit failure or button stuck.
Failure
Conduct Functional Test: Button Test.
B1583
Dim Panel Decrease Input Circuit
Dim Increase circuit failure or button stuck.
Failure
Conduct Functional Test: Button Test.
B1875
Turn Signal / Hazard Switch Signal Hazard circuit failure or button stuck. Conduct
Circuit Failure
Functional Test: Button Test.
B2675
Trip reset button stuck Trip reset
Conduct Functional Test: Button Test.
circuit failure or button stuck.
B2680
Odometer Changed
Permanent DTC indicating that Odometer has
been manually reset. - No Action Required
B2681
PRND Sender Failure
Invalid PRND data detected, Conduct Functional
Test: Multifunction Output Test. Check PCM
PRND data
B2895
Trip Computer Mode Switch Circuit Trip computer circuit failure or button stuck.
Failure
Conduct Functional Test: Button Test.
G86737 en
413-01-12 Instrument
Cluster 413-01-12
DIAGNOSIS AND TESTING (Continued)
Display
Description
Action
B2896
Odometer Data Failure
Internal odometer data failure, disconnect power,
wait 10 seconds and re-apply power. Run self test.
If DTC is still present, Conduct Functional Test:
Voltage Supply Test.
U1900
CAN Communication Bus Fault -
Missing message from external module detected.
Receive Error
Use WDS to diagnose module and check module
indicated for correct operation.
U2196
Invalid ‘Engine RPM’ data
PCM output data failure. Check PCM module.
Conduct Functional Test: Gauge Test
U2197
Invalid ‘Vehicle Speed’ data
PCM output data failure. Check PCM module.
Conduct Functional Test: Gauge Test
U2198
Invalid ‘Fuel Pulse’ data
PCM output data failure. Check PCM module.
Conduct Functional Test: Gauge Test
U2199
Invalid ‘Engine Coolant
PCM output data failure. Check PCM module.
Temperature’ data
Conduct Functional Test: Gauge Test
U2200
Invalid ‘ODO Count’ data
PCM output data failure. Check PCM module.
Conduct Functional Test: Input & Data Test.
Pid Chart
Parameter Name
Description
Data Type
CCNT
Number of Continuous Trouble Codes Set
DTC(s)
NTCSDT
Number of Trouble Codes Set due to Diagnostic
DTC(s)
Test
VBATT_VAL
System Battery Voltage Value
Volts
LCD_ILLUM
LCD Illumination Level
% duty cycle on time
PWM_ILLUM
Illumination PWM value
% duty cycle on time
PWM_DUTY1
PWM Duty Cycle #1
% duty cycle on time
PWM_DUTY2
PWM Duty Cycle #2
% duty cycle on time
ODO_M
Odometer
Kilometers
TRIP_MET
Vehicle Trip Odometer - Metric
Kilometers
TRIPB_MET
Vehicle Trip Odometer - B - Metric
Kilometers
TRIP_TIME
Trip
Minutes
FUEL_ECON
Instantaneous Fuel Economy - Metric
l/100km or l/hr
AVG_FUEL
Average Fuel Economy - Metric
l/100km or l/hr
VEH_SPD
Vehicle Speed
Kilometers / hour
TRIP_CMP
Trip Computer
Kilometers
FUEL_LEVEL
Fuel Level Input
% FULL
SPD_IND
Speedometer Gauge Indicator Control
KPH
TACH_IND
Tachometer Gauge Indicator Control
RPM
TEMP_IND
Engine Temperature Gauge Pointer Place -
Degrees Celsius
Degrees C.
FUEL_SNDR
Fuel Sender
Ohms
TEMP_GA
Temperature Gauge
% MAX
CLU_STAT
ECU Operating States
Default / Std. Diag Mode
G86737 en
413-01-13 Instrument
Cluster 413-01-13
DIAGNOSIS AND TESTING (Continued)
Parameter Name
Description
Data Type
TRANSGEAR
Gear selected
Unknown
Reverse
Forward Drive
Forward Drive 2
Forward Drive 3
Forward Drive 4
Forward Drive 5
Park
Drive "D"
Neutral
Invalid Data
DIMMER_S3
Dimmer Switch Input Status
NO Keypress
Dimmer Switch
Illumination UP / Dimmer
Switch
Illumination DOWN
Illumination UP + DOWN
FUEL_MODE
Fuel Economy Display Mode
Litres per 100km
Litres per hr
LCD_DSPL
LCD Segment Display
On
Off
BEM_MSG
BEM Missing Message
—
CDU_MSG
ACM Missing Message
—
ABS_MSG
ABS / TCS / IVD Missing Message
—
PCM_MSG
Powertrain Control Module Missing Message
—
PARKBRAK
Park Brake Applied Warning Lamp
ON/OFF
TONE_REQ
Tone request - Airbag fault warning
ACTIVE/NON ACTIVE
RESETSW
Reset Switch
ACTIVE/NON ACTIVE
P_LMP_SW
Park Lamps Switch
ACTIVE/NON ACTIVE
HAZ_SW
Hazard switch
ACTIVE/NON ACTIVE
RT_SWITCH
Right Turn Switch
ACTIVE/NON ACTIVE
LT_SWITCH
Left Turn Switch
ACTIVE/NON ACTIVE
AUTOLMPSW
Autolamp ON Switch
ACTIVE/NON ACTIVE
SBLTMP
Seat Belt Lamp Driver Output State
ACTIVE/NON ACTIVE
MENU_SW
Menu Switch
ACTIVE/NON ACTIVE
HAZ_WARN
Hazard Warning
ACTIVE/NON ACTIVE
LMPONWRN
Lamp ON
ACTIVE/NON ACTIVE
AUD_WARN
Audible warning ON
ACTIVE/NON ACTIVE
LHS_CURNT
* Left Hand Side Indicator Current Draw
Amps.
*RHS_CURNT Right Hand Side Indicator Current
Amps.
Draw
* Output current value only valid whilst globes are
Cluster CAN Transmission Data
being driven.
Damped fuel level
CAN Data Information
Instantaneous fuel input
The CAN interface facilitates the information transfer
Fuel empty
between the electronic modules in the vehicle and
Fuel sender fail
provides a means for diagnostics interrogation.
Park lamps on
In normal operating conditions, with ignition activated,
Park brake on
the cluster will receive and transmit the following
information.
Auto headlamps input
Battery voltage level
G86737 en
413-01-14 Instrument
Cluster 413-01-14
DIAGNOSIS AND TESTING (Continued)
Switches illumination level
Tx Module
LCD illumination level
Central
Overspeed active
Display Unit
Average Speed
Overspeed mode switch
(CDU)
Average Economy Mode
Overspeed up switch
Average Economy
Overspeed down switch
Travel Time
Reset average speed
Range
Reset average economy
Instantaneous Economy mode
Reset trip time
Instantaneous Economy
External LCD illumination on
Display DTE
Body
Front right door
Electrics
Odometer
Front left door
Module
Odometer overflow
Rear right door
(BEM)
Rear left door
Cluster CAN Receive Data
Boot lid door
Tx Module
Rear demist
Powertrain
Engine RPM
Low wash warning
Control
Vehicle speed
Headlamp fail
Module
Coolant temperature
Hazard flash request
(PCM)
Odometer count
Security warning on
Fuel pulse
Traction
TCS warning
Control
Oil pressure warning
System (TCS)
Cruise warning
ETC warning
Flash security warning
Manual Transmission
Transmission mode
PRND
Transmission overheat
Transmission fail
Symptom Chart
Condition
Source
Action
ABS Warning Indicator always
Circuit.
Conduct Pinpoint Test ‘ABS warning
ABS module
activated / inoperative
Test’.
Instrument cluster.
Circuit.
Conduct Pinpoint Test ‘Airbag Warning
Airbag warning always on.
Airbag module
Test’.
Instrument cluster.
Alternator Warning Indicator always
Circuit.
Conduct Pinpoint Test ‘Alternator
activated / inoperative
Instrument cluster.
Warning Test’.
Autolamps always activated /
Circuit.
Conduct Functional Test: Input & Data
Switch.
Test.
inoperative
Conduct Pinpoint Test ‘Autolamps
Instrument cluster.
Indicator Test’.
Audio Illumination inoperative with
Circuit - CAN wakeup.
Conduct Pinpoint Test ‘CAN wakeup
CDU.
ignition OFF
Test’.
Instrument cluster.
Brake Fail Warning Indicator always
Circuit.
Conduct Pinpoint Test ‘Brake Fail
Switch.
activated / inoperative
Warning Test’.
Instrument cluster.
G86737 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст