Ford Falcon. Manual — part 339
413-07-5 Clock 413-07-5
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
A4
VOLTAGE CHECK
Disconnect Clock.
Yes
Replace Clock.
Connect multimeter to pin ?? of Clock wiring connector and measure
voltage while varying IC illumination control switches.
No
Go to B1
Does the voltage vary?
PINPOINT TEST B : CLOCK NOT WORKING
Test Step
Result / Action to Take
B1
CORRECT CONNECTION
Remove Clock from Instrument panel.
Yes
Continue.
Is the connector fully engaged ?
No
Engage connector and check functionality. Go to
B2 if still not functioning.
B2
VOLTAGE CHECK
Disconnect Clock.
Yes
Replace clock.
Set multi meter to measure 12 volts and connect multimeter across
pins.
No
For (Y-B) and (B-LG) wires of Clock wiring connector and measure
Check wire integrity.
voltage.
Is 12 volts present.
PINPOINT TEST C : CLOCK LOSING / GAINING TIME
Test Step
Result / Action to Take
C1
VOLTAGE CHECK
Yes
Continue.
Is battery voltage above 12 volts?
No
Refer batter service.
C2
CLOCK CONDITION
Yes
Replace clock.
Does clock loose / gain more than five seconds every 24 hours?
No
Clock functioning correctly.
G86737 en
413-07-6 Clock 413-07-6
REMOVAL AND INSTALLATION
Clock
Removal
1. To remove the analogue clock, gently slide a flat
blade item ( eg. large screw driver) into the rear
margin, closest to the windscreen, and pry the
clock panel upwards to disengage the two clips.
2. Rotate this end up to disengage the interlocking
fingers attaching the clock panel to the air register
panel.
3. Disconnect the electrical connector.
Installation
1. To install the clock, first make the electrical
connection.
2. Ensure clock functions and illumination varies.
3. Ensure all interlocking fingers are aligned and
rotate the clock panel down wards to drive the
panel home and engage the two clips.
G73350 en
413-08-1
Interior Command Centre
413-08-1
SECTION : 413-08 Interior Command Centre
VEHICLE APPLICATION : 2003.0 BA Falcon
CONTENTS
PAGE
DESCRIPTION AND OPERATION
Interior Command Centre . . . . . . . . . . . . . . . . . . . . . . . . . .413-08-2
ICC Handling and Storage . . . . . . . . . . . . . . . . . . . . . . . . . 413-08-2
DIAGNOSIS AND TESTING
Interior Command Centre . . . . . . . . . . . . . . . . . . . . . . . . . .413-08-4
Principles
Operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . .413-08-4
Inspection and Verification . . . . . . . . . . . . . . . . . . . . . . . . ...413-08-6
Symptom
Chart
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413-08-9
Service
Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . 413-08-11
REMOVAL AND INSTALLATION
Interior Command Centre (ICC) . . . . . . . . . . . . . . . . . . . . . . ...413-08-19
Service Body Computer (BEM) . . . . . . . . . . . . . . . . . . . . . . ...413-08-23
Service Remote Key Receiver (RKR) . . . . . . . . . . . . . . . . . . . . .413-08-25
Service Air Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 413-08-25
Cabin Temperature Sensor . . . . . . . . . . . . . . . . . . . . . . . . ..413-08-26
413-08-2
Interior Command Centre
413-08-2
DESCRIPTION AND OPERATION
2. Warranty is void if ICC is dropped, handled
Interior Command Centre
roughly or treated outside of these guidelines.
The Interior Command Centre includes audio, climate 3. The ICC must not to be tilted beyond 90 degrees
control and auxiliary controls (i.e.. Door locks,
from upright. At no stage can the ICC be shocked
courtesy lamps, interior lamps) displayed in a
or excessively vibrated. Such action may damage
centralised area. System status is displayed on a
the Audio mechanism. Warranty will be void if
screen built into the instrument panel.
these conditions are not met.
The Interior Command Centre screen is
4. The ICC contains many delicate mechanical and
monochromatic for low series screens. High series
electrical components. Special care must be
vehicles receive a colour screen. Vehicles with
taken. The following are important :
Sat-Nav optioned also receive a colour screen.
1. DO NOT scratch the Class A appearance
Features of each screen are highlighted below:
surfaces.
1. LCD for low series:
2. DO NOT apply excess pressure to the screen
Monochromatic
surface at any time.
Uses preset symbols to display information
3. DO NOT apply force in excess of 10 kg to any
appearance surface of the ICC.
2. TFT for high series:
4. DO NOT touch the pins of the Self-aligning
Full colour
connector at the rear of the Audio Module.
Reconfigurable screen settings
5. DO NOT touch the Cabin Temperature
Video input for Sat-Nav, as well as preset
Sensor (refer illustration).
screens
6. DO NOT apply pressure to any of the
The Interior Command Centre consists of the
switches, knobs or buttons exceeding 5 kg.
following base components:
7. AVOID all contact with dirt, dust, metal flakes,
Audio features:
metal shavings.
LCD screen
5. The ICC is sensitive to Electro Static Discharge.
Loud button
Avoid all contact with static electricity and all
Tuning/Track select
precautions must be undertaken to ensure
adequate grounding of the repair technician and
Auto store
the ICC Module outside of the vehicle
CD eject button
environment to avoid ESD damage.
CD mode button
6. Avoid all contact with any liquids : soft drinks,
Mode select button
water, hot drinks, alcohol, etc. ICC electronic
Audio On/Off/Volume button
components will be damaged by any contact with
liquids.
FM/AM select buttons
7. ICC is not to be disassembled except for
HVAC features:
recognised service items. The only recognised
A/C on/off
service items are the Body Computer (BEM), Air
Automatic Climate Control On/Off
Register and Remote Key Receiver.
These individual components are to be removed
Driver/Passenger temp settings
in tact as required, according to the Service
Front windscreen demist
Manual requirements. Components are not to be
Air distribution modes
tampered with or else component warranty is
Fresh/Recirc air inlet
voided.
Blower fan speed
8. ICC storage temperature is never to exceed the
range -30
°C to +85°C.
Ambient temperature display
9. Adhesive labels cannot be used on CD’s as they
Rear demist (heated backlight)
can peel off and damage internal mechanisms.
Door lock
The use of a disc that deviates from above
Dome lamp
industrial standards, use of soiled, scratched,
For further information regarding the function of each
dented, cracked, or warped discs and use of
button, please refer to the Owners Guide.
pirated discs, etc. will void a warranty claim.
Sumitomo will not accept a warranty claim if any
ICC Handling and Storage
part of the audio unit or ICC has been damaged
by the use of an "unsupported" disc.
1. ICC must be handled appropriately. Grab points
are shown in illustrations.
G73346 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст