Ford Falcon. Manual — part 409
501-05-5
Interior Trim and Ornamentation
501-05-5
REMOVAL AND INSTALLATION (Continued)
2. Lever out and remove grab handle cap, taking
7. Remove screws from grab handle.
care not to mark surface of door trim grab handle.
8. Disengage door trim retention clips by pulling door
3. Remove Interior Latch Release. For additional
trim away from sheet metal (in direction of arrow),
information, refer to Door Latch Interior Release in
starting at lower edge.
this section.
NOTE: Pull along edge of trim; do not use the
grab handle.
4. Remove 2 lower screw covering caps and screws.
5. Remove Rear upper screw fixing.
6. Remove Front upper screw fixing.
Item
Description
1
Front door trim
Item
Description
2
Screw
1
Front door trim
9. When trim is loose, lift up and over lock rod
2
Interior latch release
(indicated by circle).
3
Screw
10. Disconnect electrical connectors if required and
remove door trim panel assembly.
Installation
1. Reverse removal procedure.
Rear Door Lo Series Trim Panel
Removal
NOTE: Rear door trim with pull cup / window winder.
For rear door trim with power windows, refer to Front
Door Trim notes for removal and installation.
1. Remove pull cup screw.
2. Remove pull cup.
3. Remove
Window
Winder.
G11871 en
501-05-6
Interior Trim and Ornamentation
501-05-6
REMOVAL AND INSTALLATION (Continued)
4. Remove Door Latch Interior Release handle.
Rear Quarter Trim Panel — Wagon
Removal
1. Follow removal instructions shown in figure.
Item
Description
1
Screw
2
Ash tray
Item
Description
3
Rear door trim - Lo Series
1
Quarter panel trim
5. Remove 2 lower screw fixings.
2
Sunvisor check block
6. Remove forward upper screw fixing.
3
Luggage compartment carpet
7. Remove rear upper screw fixing.
4
Wheel arch
5
Screw
Installation
1. Reverse removal procedure.
Quarter Trim Panel — Ute
Removal
1. Remove the right and left hand side quarter trim
panel as shown.
Item
Description
1
Rear door trim - Lo series
2
Screw
8. Disengage door trim retention clips by pulling door
trim away from sheet metal. Start at lower edge,
working around the edge of the door trim.
9. Disconnect electrical connectors if required and
remove door trim panel assembly.
Installation
Item
Description
1. Reverse removal procedure.
1
Trim panel
2
Locator plug
Installation
1. Reverse the removal procedure.
G11871 en
501-05-7
Interior Trim and Ornamentation
501-05-7
REMOVAL AND INSTALLATION (Continued)
Loadspace Trim Panel — Ute
Liftgate Lower Trim
Removal
Removal
1. Follow removal instructions shown in figure.
1. Follow removal instructions shown in figure.
Item
Description
Item
Description
1
Clip fir tree
1
Liftgate lower trim
2
Cover Assy Back panel trim
2
Pull strap
3
Child restraint anchorage
3
Scrivet
4
Nut and washer Assy. M6
Installation
5
Clip
1. Reverse removal procedure.
Installation
Liftgate Upper Trim
1. Reverse removal procedure.
Removal
Parcel Shelf
1. Follow removal instructions shown in figure.
Removal
1. Carefully remove the barbed clips. (4 x No. 1 and
1 x No. 2)
2. Lift the Package tray trim from the parcel shelf
sheet metal.
Item
Description
1
Liftgate upper trim LH
2
Liftgate upper trim RH
3
Push on clip (Type A)
4
Push on clip (Type B)
Item
Description
Installation
1
Barbed clip no. 1
1. Reverse removal procedure.
2
Barbed clip no. 2
Installation
1. Reverse the removal procedure.
G11857 en
501-05-8
Interior Trim and Ornamentation
501-05-8
REMOVAL AND INSTALLATION (Continued)
8. Remove headlining via liftgate opening.
Sunvisor
Removal
1. Remove sunvisor as shown in figure.
Item
Description
1
Headlining
2
Barbed clip
Item
Description
3
Sunvisor check block
1
Sunvisor
Installation
2
Screw
1. Reverse removal procedure.
3
Screw
NOTE: Care should be taken when handling
Installation
headlining not to be bend unnecessarily.
1. Reverse the removal procedure.
Headliner — Sedan
Headliner — Wagon
Removal
Removal
1. Remove grab handles and hook.
1. Remove grab handles and hook.
2. Remove sunvisors and check blocks.
2. Remove sunvisors and check blocks.
3. Remove A,B,C and pillar interior trim parts.
3. Remove A,B,C and D pillar interior trim parts.
4. Remove dome light lens and body and disconnect
4. Remove dome light lens and body and disconnect
wiring.
wiring.
5. Remove rear courtesy light lens and body and
disconnect wiring.
6. Remove upper sections of door and liftgate
opening weatherstrip.
7. Remove barbed clips.
Item
Description
1
Headlining
2
Barbed clip
3
Sunvisor check block
NOTE: Avoid folding or creasing the headlining during
removal.
G11857 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст