Ford Falcon. Manual — part 410
501-05-9
Interior Trim and Ornamentation
501-05-9
REMOVAL AND INSTALLATION (Continued)
Installation
2. Undo spare wheel board tie down and remove
spare wheel cover.(Refer removal of spare wheel
1. Reverse removal procedure.
cover in this section.)
Headliner — Ute
Removal
1. Remove A,B,C pillar interior trim parts.
2. Remove sunvisors and check blocks.
3. Remove grab handles and hook.
4. Locate interior light wiring connector at base of
"A" pillar trim and disconnect.
5. Remove barbed clips.
6. Remove headlining via door opening.
3. Remove 3 fir tree clips from front of cover lower
back.
Item
Description
1
Panel assy. roof trim
Installation
1. Reverse removal procedure.
NOTE: Care should be taken when handling
Item
Description
headlining not to bend unnecessarily.
1
Fir tree clip
4. Remove cover lower back with an upwards
Luggage Compartment Cover Lower
motion.
Back
NOTE: Be careful not to damage hooks located
on both the LH and RH extremities.
Removal
1. Lift
carpet.
Installation
1. Reverse removal procedure.
G11864 en
501-05-10
Interior Trim and Ornamentation
501-05-10
REMOVAL AND INSTALLATION (Continued)
2. Fold carpet from underneath seat backs into the
Luggage Compartment Quarter Trims
luggage compartment.
Removal
3. Remove
carpet.
1. Remove 2 fir tree clips on luggage compartment
side.
NOTE: On high series vehicles that have luggage
net fitted, luggage net hook will be removed
instead of a fir tree.
Installation
1. Reverse removal procedure.
Spare Wheel Board
Removal
Item
Description
1. Fold carpet back.
1
Quarter trim
2
Fir tree clip
3
Fir tree clip
4
Plug
2. Lower seat back in cabin. (Refer to Section
501-10.)
3. Loosen package tray trim at front edge.
4. Remove 2 fir tree clips located behind seat back.
2. Undo spare wheel tie down.
Installation
1. Reverse removal procedure.
Luggage Compartment Load Floor
Carpet
Item
Description
Removal
1
Strap
1. Lower seat back in cabin. (Refer to Section
501-10.)
2
Cover
G11864 en
501-05-11
Interior Trim and Ornamentation
501-05-11
REMOVAL AND INSTALLATION (Continued)
Item
Description
Installation
3
Spare wheel
1. Reverse removal procedure.
3. Remove spare wheel board.
Decklid Trim
Installation
Removal
1. Reverse removal procedure.
Short Wheel Base
Package Tray Insulator
1. Remove 14 fir tree clips.
Removal
2. Slide trim off decklid latch.
1. Remove both LH and RH quarter trims.(Refer
removal of quarter trim in this section.)
2. Remove package tray trim. (Refer to removal of
Parcel Shelf in this section.)
3. Remove 2 fir tree clips located on front edge of
package tray insulator behind seat backs.
Item
Description
1
Decklid trim - SWB
2
Fir tree clips
Long Wheel Base
1. Remove 13 fir tree clips.
Item
Description
2. Remove
pulldown
handle.
1
Package tray insulator
2
Fir tree clip
4. Remove clips on rear edge of package tray
insulator.
Item
Description
1
Decklid trim - LWB
2
Fir tree clips
3
Pull down handle
Item
Description
3. Slide decklid trim off decklid latch.
1
Package tray insulator
Installation
2
Plastic snap clip
1. Reverse removal procedure.
5. Bend part through the middle and slide through
pass through into luggage compartment.
G11869 en
501-05-12
Interior Trim and Ornamentation
501-05-12
REMOVAL AND INSTALLATION (Continued)
Front Door Watershield
Front Inner Scuff Plate (RH)
Removal
Removal
1. Remove watershield as shown in figure.
1. Remove plug from front of plate (dash panel side).
2. Remove plug from door side.
Item
Description
1
Pull through hole in watershield
2
Front door trim watershield
Installation
1. Reverse removal procedure.
Rear Door Watershield
Removal
1. Remove watershield as shown in figure.
3. Pull scuff plate towards centre of vehicle.
Installation
1. Reverse removal procedure.
Installation
1. Reverse removal procedure.
G11869 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст