Ford Falcon. Manual — part 253
307-05-15
Automatic Transmission External Controls
307-05-15
REMOVAL AND INSTALLATION (Continued)
Selector Lever Cable
Removal
1. Release locking tab from the Transmission Cable
Mount.
2. Disconnect the cable from the housing.
3. Use a screwdriver to release the cable push rod
from the cable arm.
Installation
1. To reassemble simply push the cable end fitting
back into the pin.
I6 Selector Cable
G77045 en
307-05-16
Automatic Transmission External Controls
307-05-16
REMOVAL AND INSTALLATION (Continued)
V8 Selector Cable
G77045 en
308-01-1 Clutch 308-01-1
SECTION : 308-01 Clutch
VEHICLE APPLICATION : 2003.0 BA Falcon
CONTENTS
PAGE
SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308-01-2
DESCRIPTION AND OPERATION
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308-01-3
Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..308-01-3
Clutch
Function
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308-01-3
DIAGNOSIS AND TESTING
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308-01-6
Symptom
Chart
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308-01-6
GENERAL PROCEDURES
Pressure Plate Inspection . . . . . . . . . . . . . . . . . . . . . . . . . ..308-01-8
Clutch Disc Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . ...308-01-8
Clutch Pressure Plate Adjustment (XR6 Turbo Variant) . . . . . . . . . . . . . . 308-01-8
REMOVAL AND INSTALLATION
Disc and Pressure Plate . . . . . . . . . . . . . . . . . . . . . . . . . . 308-01-9
Flywheel — I6 (all variants including XR6 Turbo) . . . . . . . . . . . . . . . . 308-01-10
Flywheel — All V8 Vehicles (incl XR8 & GT) . . . . . . . . . . . . . . . . . ...308-01-11
Pilot Bearing — All Vehicles . . . . . . . . . . . . . . . . . . . . . . . . 308-01-11
DISASSEMBLY AND ASSEMBLY
Flywheel Auto Flex-Plate (XR6 Turbo only) . . . . . . . . . . . . . . . . . . .308-01-13
Ring Gear — All Vehicles except XR6 Turbo . . . . . . . . . . . . . . . . . ..308-01-13
Ring Gear — XR6 Turbo only . . . . . . . . . . . . . . . . . . . . . . . ..308-01-14
308-01-2 Clutch 308-01-2
SPECIFICATIONS
Torque Specifications
Description
Nm
CSC to clutch housing
9.5
CSC to pipe fitting nut
14
CSC Bleed screw
8
Clutch pressure plate to flywheel
I6
20
V8
48
Flex plate to flywheel disc (Turbo only)
60
Flywheel to crankshaft
I6
75
V8
80
Dowel insertion depth in flywheel
(Proud of friction face)
I6
8mm
XR6 Turbo
10.5mm
V8
11.5mm
NOTE: The V8 flywheel is designed so that the dowel
will bottom out at the correct insertion depth.
G86726 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст