Ford Falcon. Manual — part 252
307-05-11
Automatic Transmission External Controls
307-05-11
REMOVAL AND INSTALLATION (Continued)
2. Disconnect the four nuts that attach the housing
3. Remove the centre console and other associated
to the floorpan.
components. For addition information, refer to
section 501-12.
4. Place the selector lever in the ’P’ position.
5. Raise
the
vehicle.
6. Reconnect the four nuts that attach the housing to
the floorpan.
3. Lower the vehicle.
4. Remove the centre console and other associated
components. For addition information, refer to
section 501-12.
5. Detach the back light bulb/wiring and selector
cable.
7. Hold the transmission shift rod and engage Park
on the transmission by pushing the shift rod as far
forward as possible.
8. Install the shift rod on the lower selector lever.
I6
6. Remove the whole floor shift housing by lifting
vertically.
Installation
1. Install the whole floor shift housing by lifting
vertically.
V8
2. Attach the back light bulb/wiring and selector
cable.
G77041 en
307-05-12
Automatic Transmission External Controls
307-05-12
REMOVAL AND INSTALLATION (Continued)
9. Tighten the lock nut to the required torque to 28
4. Remove metal Bucket
Nm.
Remove two washers.
10. Lower the vehicle and check transmission
Remove Gasket (new gasket to be used when
operation in each selector lever detent position.
assembling to original condition).
11. Check that the mode light functions correctly.
Remove metal Bucket (pressing).
Bucket (Metal Pressing)
Replace with new.
Installation
Removal
1. To install, reverse the removal procedure.
1. Remove Centre Console and other associated
components. For additional information, refer to
Section 501-12.
2. Remove shifter assembly from vehicle. For
additional information, refer to Gearshift assembly
in this section.
3. View before and after replacement of damaged
Bucket.
Item
Description
1
Star washer
2
Gasket
3
Metal bucket
Base and Lever Assembly
Removal and Installation
1. Remove Centre Console and other associated
components. For additional information, refer to
Section 501-12.
G77041 en
307-05-13
Automatic Transmission External Controls
307-05-13
REMOVAL AND INSTALLATION (Continued)
2. Remove shifter assembly from vehicle. For
6. Disassemble and rebuild the bottom part of the
additional information, refer to Gearshift assembly
assembly. Refer to Bucket Replacement in this
in this section.
section.
3. View before and after replacement.
4. Disassemble and rebuild the top part of the
Item
Description
assembly. Refer to Housing Sub Assembly
1
Selector handle
Replacement in this section.
2
Screw
5. Replace faulty sub assembly.
3
Housing assembly
4
Lever assembly
5
Metal bucket
6
Gasket
7
Star washer
Spring Leaf Detent
Removal and Installation
1. Remove Centre Console and other associated
components. For additional information, refer to
Section 501-12.
G77044 en
307-05-14
Automatic Transmission External Controls
307-05-14
REMOVAL AND INSTALLATION (Continued)
2. Remove shifter assembly from vehicle. For
Reverse disassembly process when
additional information, refer to Gearshift assembly
rebuilding to original condition.
in this section.
3. View before and after replacement of damaged
spring.
Item
Description
1
Star Washer
4. Remove damaged spring.
2
Gasket
Remove two washers.
3
Metal Bucket
Remove gasket (new gasket to be used when
assembling to original condition).
4
Screw
Remove metal pressing.
5
Spring Leaf Detent
Undo and remove screw.
Remove damaged spring. Place new spring
on the Base and secure with the screw.
G77044 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст