Ford Aerostar (1997 year). Manual — part 10
37
How to tune radio stations
There are four ways for you to tune in a
particular station. You can manually locate the
station using the “SCAN/TUNE” button,
“SEEK” the station, “SCAN” to the station or
select the station by using the memory buttons,
which you can set to any desired frequency.
These four methods are described below.
❑
Using the “TUNE” function (Stereo Radio)
You can change the frequency up or down
one increment at a time (FM changes in
increments of 200 kHz; AM changes in
increments of 10 kHz) by first pressing the
“SCAN/TUNE” button twice (display shows
“TUNE”), then —
within approximately five
seconds
—pressing and releasing either the
right
a
or left
b
side of the “SEEK” button.
To change frequencies quickly, press and
hold down
either the right or left side of the
“SEEK” button.
Manual tuning adjusts your radio to any
allowable broadcast frequency, whether or
not a station is present on that frequency.
(See
All About Radio Frequencies
in this
section.)
❑
Using the “SEEK” function
This feature on your radio allows you to
automatically select listenable stations up or
down the frequency band. Press the right
(
a
) side of the “SEEK” button to select the
next listenable station up the frequency band.
Press the left (
b
) side of the button to select
the next listenable station down the
frequency band. By holding the button down,
listenable stations can be passed over to reach
the desired station.
38
❑
Using the “SCAN” function
Pressing the “SCAN/TUNE” button once
enters the scan mode (display will indicate
“SCN”). Pushing the right (
a
) side of the
“SEEK” button will begin the scan mode up
the frequency band, stopping on each
listenable station for approximately a
five-second sampling. Pushing the left (
b
)
side of the “SEEK” button will begin the scan
mode down the frequency band, again
stopping on each listenable station for
approximately a five-second sampling.
To stop the scan mode on the presently
sampled station, press the “SCAN/TUNE”
button again.
❑
Setting the Station Memory Preset buttons
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
FM stations (5 in FM1 and 5 in FM2).
Follow the easy steps below to set these buttons
to the desired frequencies:
1.
Select a band, then select a frequency.
2.
Press one of the memory buttons and hold
the button until the sound returns. That
station is now held in memory on that
button.
3.
Follow the two steps above for each station
memory preset button you want to set.
NOTE:
If the vehicle’s battery is disconnected,
the station memory preset buttons (if
programmed in auto mode) will need
to be reset.
39
❑
Using the Automatic Memory Load feature
You can activate the
Auto Memory Load
feature by pressing and holding the “AUTO
PRESET” button
for approximately three
seconds
. Auto Memory Load sets all memory
buttons in AM, FM1 and FM2 sequentially by
seeking out the first five strong stations for
the respective band and storing them in
memory buttons 1-5. (FM2 will store the
second set of strong stations from the FM
band.)
With Auto Memory Store, you can continually
set strong stations into your memory buttons
without losing your existing memory presets,
which is especially helpful while traveling. Your
radio will automatically set your memory
buttons to the strong local stations so you don’t
have to continually manually tune to existing
stations.
Activate Auto Memory Store by pushing the
“AUTO PRESET” button once. Your radio will
set the first five strong stations of the band you
are in (AM, FM1 or FM2) into the memory
buttons. The display will show “AUTO,” then
run through the frequencies, stopping
momentarily on the stations being set into the
memory buttons. The radio is now in the
“AUTO” mode and the display will show
“AUTO” each time a preset is activated.
NOTE:
If there are fewer than five strong
stations in the frequency band, the
remaining unfilled buttons will store
the last strong station detected on the
band.
After all stations have been filled, the radio will
begin playing the station stored on memory
button 1.
40
To deactivate the Auto Memory Store mode and
return to the manually-set memory button
stations (or those stations set using Auto
Memory Load), simply push the “AUTO
PRESET” button. Display will show “AUTO”
then “OFF.” The next time Auto Memory Store
is activated on that band, the radio will store the
next set of five strong stations.
Adjusting the tone balance and speaker
output of your radio
❑
Increasing or decreasing bass response
Push the “AUDIO” button repeatedly until
the display reads “BASS.” Push the “+” side
of the “VOL” button to increase bass (more
“lows”), and push the “-” side to decrease
bass (less “lows”).
❑
Increasing or decreasing treble response
Push the “AUDIO” button repeatedly until
the display reads “TREB.” Push the “+” side
of the “VOL” button to increase treble (more
“highs”), and push the “-” side to decrease
treble (less “highs”).
❑
Adjusting speaker balance
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the “AUDIO” button
repeatedly until the display reads “BAL.”
Push the “+” side of the “VOL” button to
shift the sound to the right speakers, and
push the “-” side to shift the sound to the
left speakers.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст