Chery B14. Manual — part 28

2.3.2.1 Check the position of scuttle; check clearance between scuttle and roof holes; check

scuttle motor. If there is strange noise, find the reason of that.

2.3.2.2 Check if there is damage of scuttle weather strip; check if there is friction of the scuttle

guide and find the reason of strange noise.

2.3.3 Solve method:

2.3.3.1 Reassemble the scuttle glass referring to glass assembly steps and make sure the

clearance between glass and roof holes should be at the correct tolerance.

2.3.3.2 Replace the motor with strange noise (Refer to disassembly/assembly of scuttle motor).

2.3.3.3 Replace with new scuttle inner trim strip (Refer to disassembly/assembly of scuttle glass)

3 Frequently appeared fault and their check and maintenance methods

Fault

Reason

Maintenance method

Water guide pipe is block or folded

Check water guide pipe

Water

leaking Spread between scuttle glass and roof hole is too big

or glass height not good

Adjust the glass relative position

Wind

noise

When spread between scuttle glass and roof hole is

big or glass height not good, or wind deflector does

not work.

Adjust the glass relative position to correct

Connection cable, fuse or grounding cable not good

Check

connection

cable,

fuse

and

grounding cable

Scuttle control unit, scuttle motor not good

Replace scuttle control unit and scuttle

motor after checking

Sunvisor fall down from sliding guide and weather

strip is damaged

Readjust sunvisor position. Assembly or

replace weather strip.

Not

correct

start and

running

There are something inside of sliding guide

Check and get rid of something

There is guide friction when the sunvisor fall down

from guide or weather strip is damaged.

Reassembly or readjust the sunvisor and

weather strip (replace damaged parts)

(A.T.S)anti clamping function does not work

Check if there is collision between body

and wind deflector, and loose the

tensioning spring, check and get rid of

something from guide.

Wrong

start

Scuttle motor does not work

Replace motor

It is stopped caused by sun visor fall down from

guide or weather strip is damaged

Reassembly or readjust the sun visor and

weather strip (replace damaged parts)

There is collision between water guide pipe and body

Stick sponge damping around water guide

pipe

Collision between roof and scuttle frame

Paint glass cement or plastic glue between

roof and scuttle frame

Noise

when start

Spread between scuttle glass and roof hole is too big Readjust glass height and relative position

or glass height is not good

4 Maintenance note and daily service

4.1 Keep everything clean during maintenance, especially for sunvisor and weather strip.

4.2 Do not let scuttle screw fall down into sliding guide during scuttle disassembly, it will

influence the scuttle running correctly.

4.3 Be care to deal with the scuttle(especially for perpendicular direction), otherwise it will

damage the important parts inside of the sliding guide.

4.4 Operate the scuttle to completely close condition when it is need to break down the

power to scuttle during car maintenance.

4.5 The scuttle can not actuate sliding down and raise up at the same time: so at the

condition of sliding down, the scuttle can not be raised up; and at the condition of raise up,

the scuttle can not be slide down. It is necessary to shut down it and then start raise up or

sliding down.

4.6 You should not continue push the button when the scuttle is completely opened or closed,

otherwise it will cause scuttle motor and mode fault.

4.7 Clean the scuttle sliding guide at a fixed period by clean water to wash away the dust and

other particles inside of guide and rubber strip.

4.8 It may damage the scuttle glass and motor when you open the scuttle which is in a freezing

or snow covered conditions.

Chapter Eight Disassembly/Assembly of Instrument

Panel

I. Disassembly of instrument panel

accessories

1 Preparation

Tool: socket spanner, cross head screwdriver, flat head

screwdriver

Note: disconnect accumulator cathode before disassemble

electrical parts

2 Disassembly/assembly of central control panel
and fog lamp switch

2.1 Disassembly steps：

2.1.1 Disassemble central ventilator assemblies beside of

central control panel by hand.

2.1.2 Disassemble six screws to fix central control panel

and instrument panel.

Tool: cross head screwdriver

Installation torque: 1.5±0.5Nm

2.1.3 Unplug cigar lighter, switches for front and rear fog

lamps, double switch, rear windscreen defroster switch plugs.

2.1.4 Take off central control panel.

2.2 Assembly steps：

The installing steps are reverse to those for removal.

3 Disassembly/assembly of AC control panel

3.1 Disassembly steps

3.1.1 Disassemble central control panel
（Refer to disassembly steps of central control panel）

3.1.2 Unscrew 4 AC control panel fixing screws by

cross head screwdriver and take off rear plug, take off

AC control panel.

Installation torque: 1.5±0.5 Nm

3.2 Assembly steps

The installing steps are reverse to those for removal.

4 Disassembly/assembly of audio

4.1 Disassembly steps

4.1.1 Disassemble central control panel

(Refer to disassembly steps for central control panel)

4.1.2 Disassemble 4 audio fixing bolts by No.10 socket

spanner. Unplug rear plug and antenna, take off audio control

panel.

Installation torque: 9±3 Nm

4.2 Assembly steps

The installing steps are reverse to those for removal.