Chery Tiggo 5 (T21). Manual — part 518
48–
30
48
Rear Bumper Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the back door locating seat.
a. Remove 4 fixing bolts (arrow) from the back door
locating seat.
(Tightening torque: 1.5 ± 1 N·m)
b. Remove the back door left locating seat (1) and back
door right locating seat (2).
4. Remove the rear combination light assembly (fixed part) (
).
5. Remove the rear bumper assembly.
a. Raise the vehicle with a lifter, and remove the fixing
screw (1) between rear bumper assembly and rear
wheel house protector assembly (take left side as an
example).
(Tightening torque: 3 ± 1 N·m)
b. Remove 3 plastic clips (arrow) between rear bumper
assembly and rear wheel house protector assembly
(take left side as an example).
c. Remove 4 plastic clips (arrow) from the lower part of
rear bumper assembly.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing rear bumper assembly.
Appropriate force should be applied when removing rear bumper assembly. Be careful not to operate
roughly.
Try to prevent body paint surface from being scratched when removing rear bumper assembly.
RT21480380
1
2
1
RT21480360
RT21480370
48–
31
48
d. Lower the vehicle, and remove 4 fixing screws (arrow)
from the upper part of rear bumper assembly.
(Tightening torque: 3 ± 1 N·m)
e. Remove 2 fixing bolts (1) from the upper part of rear
bumper assembly.
(Tightening torque: 3 ± 1 N·m)
f. Disengage the claws from the rear bumper assembly
(take left side as an example).
g. Disconnect the connectors (arrow) from the rear
bumper assembly, and remove the rear bumper
assembly.
RT21480390
1
RT21480400
CAUTION
Avoid breaking claws when removing rear bumper assembly.
RT21480410
48–
32
48
Disassembly
1. Remove the rear towing hook cover plate.
a. Using a screwdriver wrapped with protective tape,
remove the rear towing hook cover plate claws
(arrow).
b. Remove the rear towing hook cover plate from the
rear bumper assembly.
2. Remove the rear fog light.
a. Remove 8 fixing crews (arrow) from the rear fog light.
(Tightening torque: 1.5 ± 0.5 N·m)
b. Remove the rear left fog light (1) and rear right fog
light (2) from the rear bumper assembly.
3. Remove the reversing radar sensor.
a. Press the claws on the reversing radar sensor.
b. Remove the reversing radar sensor from the rear
bumper assembly.
CAUTION
Be sure to wear safety equipment to prevent accidents when disassembly rear bumper assembly.
Appropriate force should be applied when dissembling rear bumper assembly. Be careful not to operate
roughly.
Avoid breaking claws when disassembly rear bumper assembly.
RT21480420
1
2
RT21480421
RT21480422
48–
33
48
Assembly
Assembly is in the reverse order of disassembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to wear safety equipment to prevent accidents when installing rear bumper assembly.
Try to prevent body paint surface from being scratched when installing rear bumper assembly.
CAUTION
Be sure to wear safety equipment to prevent accidents when installing rear bumper assembly.
Try to prevent body paint surface from being scratched when installing rear bumper assembly.
Make sure rear bumper is installed correctly and fitting clearance between rear bumper and body is
appropriate when installing rear bumper assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст