Chery Tiggo 5 (T21). Manual — part 95
06–
222
06
a. Disconnect ECM connector E-033.
b. Turn ignition switch to ON and check ECM connector
terminals.
11
Check ECM power supply and ground
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065069
Multimeter
Connection
Condition
Specified
Condition
E-033 (35, 20) -
E-033 (63 or 64)
Ignition switch ON
11 to 14 V
Repair or replace related wire harness
NG
Go to Diagnostic Help
OK
06–
223
06
Diagnosis Procedure
a. Check spark plug of each cylinder, and observe if the type and gap are as specified.
a. Observe if trouble occurs just after fuel is filled.
Engine starts normally, but idles roughly at anytime
1
Check air filter for blockage, and intake pipe for air leakage
Check and repair intake system
NG
2
Check if throttle is stuck
OK
Repair or replace throttle
NG
3
Check spark plug
OK
Replace spark plug
NG
4
Check throttle for carbon deposits
OK
Clean throttle
NG
5
Check injector for leakage or blockage
OK
Clean or replace injector
NG
6
Check fuel condition
OK
Replace fuel
NG
OK
06–
224
06
a. Measure compression of misfiring cylinder (
a. Check if engine ignition sequence and ignition timing are as specified.
a. Disconnect ECM connector E-033.
b. Turn ignition switch to ON and check ECM connector
terminals.
7
Check pressure of cylinder
Check engine to confirm cause of low
compression
NG
8
Check engine ignition sequence and ignition timing
OK
Check and repair ignition timing
NG
9
Check ECM power supply and ground
OK
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065069
Multimeter
Connection
Condition
Specified
Condition
E-033 (35, 20) -
E-033 (63 or 64)
Ignition switch ON
11 to 14 V
Repair or replace related wire harness
NG
Go to Diagnostic Help
OK
06–
225
06
Diagnosis Procedure
a. Check spark plug of each cylinder, and observe if the type and gap are as specified.
a. Observe if trouble occurs just after fuel is filled.
Engine starts normally, but idles roughly during warming up
1
Check air filter for blockage, and intake pipe for air leakage
Check and repair intake system
NG
2
Check spark plug
OK
Replace spark plug
NG
3
Check throttle for carbon deposits
OK
Clean throttle
NG
4
Unplug coolant temperature sensor connector, start engine and observe if engine idles
normally during warming up
OK
Check and repair wire harness or replace
sensor
OK
5
Check injector for leakage or blockage
NG
Clean or replace injector
NG
6
Check fuel condition
OK
Replace fuel
NG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст