Chery Tiggo 5 (T21). Manual — part 528
49–
23
49
C-pillar Lower Protector Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the rear left doorsill pressure plate assembly (
2. Remove the rear left door opening weatherstrip (
3. Remove the luggage compartment carpet assembly (
4. Remove the rear left seat assembly (
).
5. Remove the back door baffle plate assembly.
a. Remove 2 fixing nuts (1) from the back door baffle
plate assembly.
(Tightening torque: 1.5 ± 1 N·m)
b. Remove 2 fixing screws (arrow) from the back door
baffle plate assembly and remove the back door baffle
plate assembly.
(Tightening torque: 1.5 ± 1 N·m)
6. Remove the left C-pillar lower protector assembly.
a. Remove the fixing bolt (arrow) from the lower part of
front seat belt.
(Tightening torque: 50 ± 5 N·m)
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the C-pillar lower protector
assembly.
Appropriate force should be applied when removing the C-pillar lower protector assembly. Be careful not
to operate roughly.
Prevent interior and body paint from being scratched when removing the C-pillar lower protector
assembly.
RT21490141
1
RT21490140
49–
24
49
b. Remove the warning triangle box (for right side) in the
direction of arrow as shown in the illustration.
c. Using a screwdriver wrapped with protective tape, pry
off the back door light cover (for right side).
d. Disconnect the back door light connector (arrow) and
remove the back door light.
e. Using a screwdriver wrapped with protective tape, pry
off the rear shock absorber service cover and remove
the rear shock absorber service cover.
RT21490161
RT21490162
RT21490163
RT21490152
49–
25
49
f. Using a screwdriver wrapped with protective tape, pry
off the rear combination light service cover and
remove the rear combination light service cover.
g. Remove 5 fixing screws (arrow) from the C-pillar
lower protector assembly.
(Tightening torque: 1.5 ± 1 N·m)
h. Using an interior crow plate, pry off the clips from the
C-pillar lower protector assembly, and remove the left
C-pillar lower protector assembly.
Installation
Installation is in the reverse order of removal.
RT21490153
RT21490150
RT21490151
CAUTION
Make sure the damaged clips are replaced and the C-pillar lower protector assembly is installed in place
when installing the C-pillar lower protector assembly.
The C-pillar lower protector assembly, C-pillar upper protector and rear door opening weatherstrip should
be fitted closely after installing the C-pillar lower protector assembly.
49–
26
49
C-pillar Upper Protector Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the rear left doorsill pressure plate assembly (
2. Remove the rear left door opening weatherstrip (
3. Remove the luggage compartment carpet assembly (
4. Remove the rear left seat assembly (
).
5. Remove the left C-pillar lower protector assembly (
).
6. Remove the left C-pillar upper protector assembly.
a. Remove 3 fixing screws (arrow) from the C-pillar
upper protector assembly.
(Tightening torque: 1.5 ± 1 N·m)
b. Using an interior crow plate, pry off the clips from the
C-pillar upper protector assembly, pull out the rear
seat belt from the C-pillar upper protector assembly,
and remove the left C-pillar upper protector assembly.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the C-pillar upper protector
assembly.
Appropriate force should be applied when removing the C-pillar upper protector assembly. Be careful not
to operate roughly.
Prevent interior and body paint from being scratched when removing the C-pillar upper protector
assembly.
RT21490160
RT21490170
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст