Chery A18. Manual — part 57
III. Disassembly & assembly of the wiring harness of the right front door. . . 146
(I).Preparation . . . . . . . . . . . . . . . . . . . . . . . . . ... 146
(II).Attentions. . . . . . . . . . . . . . . . . . . . . . . . . . 146
(III).Disassembly steps. . . . . . . . . . . . . . . . . . . . . . .. 147
(IV).Assembly steps. . . . . . . . . . . . . . . . . . . . . . . .. 148
Section VII Roof Wiring Harness . . . . . . . . . . . . . . . . . . . . . . . 149
I. Wiring harness sketch . . . . . . . . . . . . . . . . . . . . . . . . 149
II. Main plug-in units explanation . . . . . . . . . . . . . . . . . . . . 150
III. Disassembly & assembly of the roof wiring harness . . . . . . . . . . .. 150
(I).Preparation . . . . . . . . . . . . . . . . . . . . . . . . . ... 150
(II).Attentions. . . . . . . . . . . . . . . . . . . . . . . . . . 150
(III).Disassembly steps. . . . . . . . . . . . . . . . . . . . . . .. 150
(IV).Assembly steps. . . . . . . . . . . . . . . . . . . . . . . .. 151
Section VIII Wiring Harness Inside Floor. . . . . . . . . . . . . . . . . . . . 152
I. Wiring harness sketch . . . . . . . . . . . . . . . . . . . . . . . . 152
II. Main plug-in units explanation . . . . . . . . . . . . . . . . . . . . 153
III. Disassembly & assembly of the inside floor wiring harness . . . . . . . .. 157
(I).Preparation . . . . . . . . . . . . . . . . . . . . . . . . . ... 157
(II).Attentions. . . . . . . . . . . . . . . . . . . . . . . . . . 157
(III).Disassembly steps. . . . . . . . . . . . . . . . . . . . . . .. 157
(IV).Assembly steps. . . . . . . . . . . . . . . . . . . . . . . .. 165
Section IX Wiring Harness of the Rear Trunk Door . . . . . . . . . . . . . . . . 166
I. Wiring harness sketch . . . . . . . . . . . . . . . . . . . . . . . . 166
II. Main plug-in units explanation . . . . . . . . . . . . . . . . . . . . 167
III. Disassembly & assembly of the rear door wiring harness . . . . . . . . . 167
(I).Attentions . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
(II).Disassembly steps . . . . . . . . . . . . . . . . . . . . . . ... 167
(III)。Assembly steps . . . . . . . . . . . . . . . . . . . . . . ... 169
Chapter I Front Compartment Cover & Trunk
I. Disassembly of the front compartment cover
1. Preparation
Tools: Socket wrench 10#, connecting rod, ratchet wrench, ring wrench 8#
2. Attention
In the process of the disassembly, pay particular attention to the suitable force using and the
careless operation is forbidden.
3. Disassembly of the front compartment cover accessories
3.1. Disassembly steps
3.1.1. Disassemble the earthed bolts with the tool, which is
shown as the figure
3.3.2. Take out the washing hose of the washing liquid
3.3.2. Press clips of 2 water nozzles below the front
compartment cover, drive water nozzles from the beneath
the front compartment cover and then take out water
nozzles from the outside
3.3. Assembly steps
Assemble according to the inverted sequence of the
4.
Disassembly
&
adjustment
of the
front
compartment cover assembly
4.1.Unscrew 4 bolts of the front compartment cover, which can
take out the front compartment cover (At the same time, through
loosening 4 bolts, the front & rear positions and left & right
positions of the front compartment cover can be adjusted).
4.2. Assembly of the front compartment cover assembly
Assemble according to the inverted sequence of the disassembly
Assembly moment:
(10±1)Nm
5. Disassembly & assembly of the air intake grille assembly
Tool: Ring wrench 8#
5.1. Disassembly steps
5.1.1. Unscrew 6 fixing bolts of the air intake grille
assembly shown as the figure with the wrench
5.1.2. Just take out the air intake grille assembly
5.2. Assembly steps
Assemble according to the inverted sequence of the disassembly
Assembly moment:
(8±0.5)Nm
6. Adjustment & assembly of the front compartment cover lock
Tools: A drill bit with 6mm diameter & electric drill
6.1. Disassembly steps
6.1.1. The lock device under the front compartment cover
is riveted with the cross bar of the water tank through the
rivet and normally not need to disassemble it, but should
take out the rivet when required disassembly
6.1.2. Take out the back guy of the front compartment
cover lock from the lock assembly under the front
compartment cover
6.2. Assembly steps
Assemble according to the inverted sequence of the disassembly
7. Disassembly of the compartment cover back guy
Tools: Phillips screwdriver
7.1. Disassembly steps
7.1.1. Disassemble 2 fixing bolts of the handle which
can open the front compartment cover in the car cab
Assembly moment:5±0.5Nm
7.1.2 .Take out the back guy from its cover
7.1.3. Take out the back guy head from the lock device
under the front compartment cover
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст