Chery B11. Manual — part 215

Chery·Maintenance Manual for Oriental Son

Automatic Transmission

47. Install the Thrust Bearing #5.

ote: do not install the thrust bearing in

e wrong direction.

8.

hrust Bearing #6 in the reverse gear and

verrning clutch.

ote: do not install the thrust bearing in

e wrong direction.

9.

lutch and then Thrust Bearing #7.

ote: do not install the thrust bearing in

e wrong direction.

N
th







4 Install the overdrive clutch hub and
T
o
N
th







4 Install the reverse gear and overrning
c
N
th








50. Fix three O-rings.

28

Chery·Maintenance Manual for Oriental Son

Automatic Transmission

51. Install four seals in the rear cover.

2. Install Thrust Bearing #8 and then the

ar cover.

3.

eed centrual gear. Replace Thrust

earing #8 to adjust the clearance to the
andard value. Refer to the following

ble and select the proper component

rial number.

ta

he axial clearance of low-speed central

ear may be easily measured by fixing the
nderdrive clutch hub.

4. After fixing the rear cover, tighten the
olt with a tightening torque of 23Nm

.

5. Fix the underdrive clutch hub.

e wrong direction.

5
re






5 Measure the axial clearance of low-
sp
B
st
ta
se
S ndard value: 0.25-0.45mm
T
g
u



5
b
(2 3Kg-m).





5







56. Fix Thrust Bearing #2.
Note: do not install the thrust bearing in
th

29

Chery·Maintenance Manual for Oriental Son

Automatic Transmission

57. Hold the input shaft and instal

nderdrive clutch.

eference:

bserve through the fixing hole of input

a

e underdrive clutch is installed in place.

8. Attach the solders (about 10mm long

nd 3.5mm in diameter) to the underdrive
lutch hub.

9.

ecial tool MD998412. Tighten the bolts

ith a tightening torque of 23Nm (2.3Kg-

).

o

0. Dismantle the set bolts, oil pump and

lder.

re th

der

s with a

dial gauge.

u
R
O
sh ft sensor on outer cover and confirm if
th



5
a
c






5 Install oil pump and bolts with the
sp
w
m
N te: do not fix the oil pump washer then.




6
so

61. Measu

e sol

thicknes

Input

2 Solders

Underdrive
clutch hub

30

Chery·Maintenance Manual for Oriental Son

Automatic Transmission

62. Select the Thrust Washer #1 of

ppropriate thickness from the following

ble:

Measured

m)

Thickness

(mm)

ID

marking

Part No.

a
ta

result (m

2.25 –2.45

1.8

18

MD754509

2.45-2.65 2.0 20

MD754508

2.65-2.85 2.2 22

MD754507

2.85-3.05 2.4 24

MD753793

3.05-3.25 2.6 26

MD753794

3.25-3.45 2.8 28

MD753795

63. Fix the Thrust Washer #1 selected in

tep 61.

4.

asher again with the special tool

B998412. Tighten the set bolts with a

ghtening torque of 23Nm (2.3Kg-m).

o

5. Measure the axial clearance of input

aft with a dial gauge and confirm that

e clearance is within the standard value

mits.
tandard value: 0.70-1.45mm

7. Fix the strainer.

S





6 Install the oil pump, set bolts and seal
w
M
ti
N te: never use an old seal washer.




6
sh
th
li
S




6

31