Chery B11. Manual — part 216
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
69. Fix the differential.
70. Dismantle the
erentia
ou
g and spa
off the
torque converter body.
71
h the sol
(about
and
in outer diameter) t
hy
torque
erter bo
2. Press and fix the differential outer ring
ith the speical tool MB990338 or
B
3. Fix the hydraulic torque converter onto
e differential body without applying any
alant. Tighten the set bolts with a
g
ote: make sure that the two short bolts
re installed as the figure shows.
5. Release the bolts and dismantle the
ydraulic torque converter, bolts and
lders.
6. Measure the thickness of the flattened
lder with a dial gauge. Add the
lect the appropriate spacer thickness and
en select the corresponding spacer from
e table below that lists all adjusting
acer thicknesses. Note: * indicates the
ickness of differnet differential cover.
diff
l bearing’s
ter rin
cer
hydraulic
. Attac
ders
10mm long
3mm
o the
draulic
conv
dy.
7
w
M 990935.
7
th
se
ti htening torque of 47Nm (4.7Kg-m).
N
a
7
h
so
7
so
measured value with 0.045 – 0.105mm*,
se
th
th
sp
th
32
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
77. Fix the spacer selected in Step 75 onto
e hydraulic torque converter body.
g
uter ring with the special tool MB990938
r MB990935.
.6mm in diameter to the spot where the
gure shows on the torque converter.
iquid sealant:
itsubishi sealant part number
D974421 or the equivalent.
0. Fix two O-rings.
hickness
mm)
ID marking
Part No.
o.
th
78. Press and fix the differential bearin
o
o
79. Apply the liquid sealant which is
1
fi
L
M
M
8
T
(
Thickness
(mm)
ID marking
Part N
0.71 71
MD754475
07
MD720945
1.07
0.74 74
MD727660
1.10
J
MD710454
0.77 77
MD754476
1.13
D
MD700270
0.80 80
MD727661
1.16
K
MD710455
0.83 83
MD720937
1.19
L
MD710456
0.86 86
MD720938
1.22
G
MD700271
0.89 89
MD720939
1.25
M
MD710457
0.92 92
MD720940
1.28
N
MD710458
0.95 95
MD720941
1.31
E
MD706574
0.98 98
MD720942
1.34
O
MD710459
1.01 01
MD720943
1.04 04
MD720944
1.37 P
MD710460
33
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
8
34
1. Fix the hydraulic torque converter and
rew the 18 bolts with a tightening torque
f 47Nm (4.7Kg-m).
2. Fix the manual control lever and
arking pawl rod.
3. Fix the manual control lever shaft
ller.
sc
o
8
p
8
ro
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
Assembly and Disassembly of Parts
put shaft
. Unfix input shaft snap ring.
. Unfix input shaft
. Unfix 2 seal rings
. Unfix the snap ring of the clutch’s
action plate
. Unfix the snap ring of the clutch’s
action plate
. Unfix the clutch plates
Type Clutch Clutch
Reaction
Disassembly of underdrive clutch and
in
1
2
3
4
re
5
re
6
plate
disc
plate
F4A42 4
4
1
7. Unfix clutch discs
. Press the clutch offsetting spring with
e special tool MD998907 and
D998924. Then unfix snap ring of clutch
ring hub.
. Unfix spring hub of clutch
0. Unfix D seal.
1. Unfix clutch offsetting spring.
2. Unfix underdrive clutch piston with
e aid of compressed air.
ssembly of underdrive clutch and
put shaft
ote:
efore assembly, apply all internal
omponents with lubricating oil. Use
aseline-lubricated D seal ring.
. Fix two D seal rings
. Fix underdrive clutch piston
. Fix clutch offsetting spring. Confirm
6.
the c
ffse
rin
ial
MD
an
assembly.
8
th
M
sp
9
1
1
1
th
13. Unfix two D seal rings.
A
in
N
B
c
V
1
2
3
that the spring hole is aligned with the
fixing mark on clutch bracket.
4. Fix D seal ring.
5
utch
ub
. Fix cl
Press
spring h
lutch o
ls of
.
tting sp
8907
g with
the spec
too
99
d
MD998924. Then fix the snap ring of
clutch spring hub.
7. Align the notch (A) of clutch disc and
reaction plate with the outer hole of
underdrive clutch bracket.
Note: dip the clutch into ATF before
35
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст