Chery B11. Manual — part 142
Chery Eastar Service Manual Body Dimension and Accessories
18
② Pry out the glass cover of left/right map
lamp from the front, and loosen the screws.
③ Detach the harness, and remove the wire of
map lamp.
Assembling requirements: The metal clips of pillar trim shall be assembled to its proper position,
without the looseness phenomenon. The shield shall match better with the ceiling and weather strip.
The adjusting baffle of seat belt tied on B and C upper shields shall operate freely and smoothly
without influencing the adjustment of seat belt. The tightening force of screw shall be appropriate to
ensure that no looseness phenomenon occurred when the sun visor operates normally. The sun visor
shall operate freely and smoothly when it works normally, without such phenomena as noise, seized
and etc. The fixed mounting shall be able to clamp the sun visor well, and it is prohibited that the sun
visor falls down during operation. The positions of assembly holes of sun visor, passenger armrest and
ceiling fixing clip shall correspond to the positions of screw holes of vehicle body, with the tolerance
of central engagement factor of ±l.5 mm, to ensure that the sun visor, passenger armrest and fixing
clip are assembled to its proper positions without any influence on the appearance. The height of the
front end of ceiling shall not disturb the assembly of front windshield, and the corner of front end of
ceiling shall be invisible from the outside, the viewing angle of which shall be in the horizontal
direction with the same height as the roof. The rim of ceiling shall match well with the door opening
weather seal and luggage weather seal, without the exposure of ceiling’s corner and untightness of
edge. And it is prohibited that there are the warp outward and sag in the corner of ceiling, which may
cause the fit unevenness of pressing plates of weather seal. The arch of rim of ceiling shall match well
with that of the upper shield of A, B and C columns, and the fit clearance shall be less than 0.2 mm.
Assemble in the reverse order of disassembly.
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
19
Disassembly/Assembly of Rear Seat Reading
Lamp
l.
Pry out the glass cover.
2.
Unscrew the two fixing screws, and detach the
harness and remove the reading lamp.
Disassembly of Three Auxiliary Handgrip
l.
Pry out the decorative cover.
2.
Unscrew the two fixing screws and remove the
and grip.
Assemble in the reverse order of disassembly.
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
20
Disassembly of Fixed Mounting of Rear
Curtain
l.
Pry out the fixed mounting.
2.
Pull out the inner roof downwards slowly from
the front windshield.
3.
Please take care the inside and outside of shield
lining after filling adhesive during reassembly.
Disassembly of Floor Carpet
Disassemble the following parts:
1.
Remove the cushioning of front/rear seat. (See
Disassembly of Seat)
2.
Remove the front/rear saddle. (See Disassembly
of Instruments)
3.
Remove the front/rear door frame plates and B
column trim. (See Disassembly of Seat Belt)
4.
Pry out the bolt cover of left foot pedal.
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
21
5. Remove the two fixing bolts for left foot
pedal pad.
6. Remove the fixing bolts for the exterior trim of fuel tank cap switch, and take out the exterior trim
Assemble in the reverse order of disassembly. Assembling requirements: The doorsill platen shall be
edged into the lower shield of B column, and the both ones shall match well, without ripple and other
phenomena. All parts of platen shall be assembled in its proper positions, and fully attach to the floor
of vehicle body, without any swollen color, wrinkle and other defects.
Disassembly of Rear Manual Curtain Infolding and Window Brake Lamp
1.
Disassemble the rear seat assy. (See Disassembly of Seat)
2.
Unscrew the fixing bolts of seat belt and seat plate. (See Disassembly of Seat Belt)
3.
Unscrew the four fixing nuts
4.
Take out the trim, unscrew the eight fixing bolts, and remove the rear curtain
PDF created with pdfFactory Pro trial version
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст