Chery A15. Manual — part 153
Chery A15 Maintenance Manual
Align tapping screw expansion nut hole center, tighten 2 tapping screws with
tightening torque 1.5±0.2N·m. Assemble license light guard board
Align trunk lock barrel with hole location so as to ensure good adaptation of
guard board and body;
Tighten 2 tapping screws, pay attention to adjust the surface difference and
movable part between the said screws and body/movable parts, feel height
difference manually, adjust based on the hand feel while tightening;
Open trunk lid;
Tighten nuts of 2 square fixed bolts;
Properly assemble connecting rod and cover plate of lock barrel (refer to
body description), and lay down trunk lid.
7. Assembling of interior dome lamp
Properly connect harness pin;
Embed ceiling mounting hole according to right position and direction, with
one end properly connected with ceiling first, and then press in dome lamp
manually.
8. Assembling of trunk light
Open trunk lid;
Properly connect harness pin;
Firstly match a wedge-position end with rear speaker cover, and then press in
lamp manually. And lay down trunk lid.
9. Assembling of high mount stop lamp
Press both ends to separate lamp holder and lamp body, pull out wire
connector;
Plug two single-end sockets of wire to male tab of windshield;
Properly assemble lamp body according to slot combination structure, pay
attention to the matching of back trough and anchor pin so as to fix lamp
body to the right position;
Properly plug wire and lamp holder, and fix the lamp holder and lamp body
to the right position.
10. Adjustment of front headlight light beam
Whether the adjustment of front headlight light beam is correct or not influences
running security directly. So dedicated instrument is allowable exclusively for the
adjustment of light beam. When adjusting, pay attention to legal regulations.
11. The following particulars shall be satisfied prior to adjustment:
Auto tire pressure meets the standard;
- 42 - CHERY AUTOMOBILE CO., LTD
Chery A15 Maintenance Manual
Automobile idling (apart from spare tire and driver's tool, driver weight shall
be included according to general regulations of sedan car);
Automobile shall be parked on horizontal road-surface or operation field;
The lens' surface of front headlight shall be clean and dirty-free;
Check to see if power source works properly, and bulb is correctly
assembled.
The two screws, which connecting front headlight can be adjusted in the
direction of up, down, left and right.
Headlight protecting cover shall be taken down when adjusting right front
headlight. Front left headlight adjusting screw and front right headlight are
arranged in symmetry, and the adjustment method is identical.
- 43 - CHERY AUTOMOBILE CO., LTD
Chery A15 Maintenance Manual
Chapter Three: Audio System
I. Control Panel
1. Power/volume/balance (when pulled out) knob
9. Manual/automatic search back
2.
Tone
knob
10.
Automatic
save/frequency
memory
3. Eject
11. Automatic scan
4.
LCD
12.
Loudness
control
5.
Cassette
seat 13.
FM/AM
band
selection
6.
Rewind 14.
Mono/stereo
shift
7.
Forward 15.
Frequency
preset
(1-6)
8. Manual/automatic search forward
16. Speaker control
II. Operations
Cassette
1. Turn knob ① rightward to power on and increase volume adequately.
2. Push the cassette into cassette seat ⑤ with the opening on the right side until the
cassette is locked, and the playback begins. LCD ④ displays “TAPE” and direction
indication “◢” or “◣”.
3. Adjust volume knob ① and tone knob ② to obtain desired sound effect.
4. Cassette player will automatically reverse at the end of tape. Manual reverse is
Chery A15 Maintenance Manual
available by pressing Rewind ⑥ and Forward ⑦ simultaneously.
5. To select desired track, press one of Forward ⑦ and Rewind ⑥, and then press
the other one to play.
6. “◢” or “◣ displayed in LCD is the playing direction of cassette, “◢” indicates
clockwise playing, while “◣” counterclockwise.
7. To stop playing or when replacing cassette, press Eject ③ to eject cassette.
Radio
1. Power, volume control and tone adjustment are the same with cassette playback.
2. Press FM/AM selection (13), LCD ④ will display the available wave bands FM1,
FM2, FM3 and AM for your option.
3. Manual/automatic tuning (band selection):
(1). Quickly press >⑧ or <⑨ for manually tuning. Repeat pressing until desired
program is locked.
(2). Keep pressing > or < for 0.5 seconds for automatic tuning, which will end
after radio signals are received. Repeat step (1) or (2) to select desired program.
4. Automatic scan tuning:
Quickly press SCN (11) to activate automatic scan. System will scan for radio signals
automatically from current frequency to higher end. Each time a radio signal is
received, the system will stop scanning for 5 seconds with the frequency flashing on
LCD and the program being played, and then the system will scan on to higher
frequency until the end is reached, where the system will automatically return to the
low end and rescan.
When one certain frequency is desired, press SCN when the frequecy is flashing on
LCD to stop scanning. Another pressing of SCN will resume automatic scan.
5. When a stereo signal is scanned, LCD ④ will display the stereo mark “ST”. When
a mono signal is desired, press “MO” (14) once, and the “ST” mark on LCD will be
replaced by “MO” mark.
Frequency Memory
Frequency memory provides a capacity of 4X6 frequencies respectively in FM1, FM2,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст