Jaguar XJ (X350). Manual — part 1014
REPAIR the short circuit to ground in the CKP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t191 : CHECK THE CKP CIRCUITS FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
C101, harness side
Battery
Pin G2
Positive terminal
Pin G1
Positive terminal
Pin F1
Positive terminal
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t192.
-> No
REPAIR the short circuit to ground in the CKP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t192 : CHECK THE CKP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin G2
Pin F1
Is the resistance between 100 Kohms - 120 Kohms?
-> Yes
GO to Pinpoint Test G549822t193.
-> No
REPAIR the out of limits resistance in the CKP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t193 : CHECK THE CKP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin G1
Pin F1
Pin G1
Pin G2
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t194.
-> No
REPAIR the out of limits resistance in the CKP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t194 : CHECK THE CMP CIRCUITS FOR SHORT CIRCUIT TO GROUND
1. Measure the resistance between:
C101, harness side
Battery
Pin G4
Negative terminal
Pin H3
Negative terminal
Pin H4
Negative terminal
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t195.
-> No
REPAIR the short circuit to ground in the CMP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
www.
G549822t195 : CHECK THE CKP CIRCUITS FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
C101, harness side
Battery
Pin G4
Positive terminal
Pin H3
Positive terminal
Pin H4
Positive terminal
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t196.
-> No
REPAIR the short circuit to power in the CMP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t196 : CHECK THE CMP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin G4
Pin H3
Is the resistance between 100 - 120 Kohms?
-> Yes
GO to Pinpoint Test G549822t197.
-> No
REPAIR the out of limits resistance in the CMP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t197 : CHECK THE CMP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin H4
Pin G4
Pin H4
Pin H3
Are the resistances greater than 100 Kohms?
-> Yes
An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other
physical damage to the harness. If no fault is found in the circuit, suspect the following
component(s): - Open circuit in sensor power line - CMP connector - CKP connector - CMP sensor -
CKP sensor - Crankshaft sensor target wheel - Camshaft sensor target wheel - ECM connector - ECM
-> No
REPAIR the out of limits resistance in the CMP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
PINPOINT TEST G549822p17 :
ACCELERATOR PEDAL POSITION
(APP) SENSORS 1 AND 2
G549822t198 : CHECK THE APP1 VALUE, WITH THE ACCELERATOR PEDAL
RELEASED
1.
Circuit
Pin
Accelerator pedal position sensor 2 - signal
01
Accelerator pedal position sensor 2 - power 02
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст