Range Rover Body Repair Manual — part 32
CHASSIS AND BODY
53
REPAIR
6. Remove bolt securing belt reel to ’B’ post,
remove belt reel.
7. Move seat fully rearwards.
8. Remove cover from seat belt stalk fixing.
Remove bolt. Collect stalk.
Refit
9. Position seat belt stalk. Secure with retaining
bolt. Tighten to
35 Nm. (26 lbf.ft). Fit bolt
cover.
10. Fit seat belt reel to ’B’ post. Secure with retaining
bolt. Tighten to
35 Nm. (26 lbf.ft)
11. Move seat fully forwards.
12. Secure seat belt to lower anchorage point. Fit
bolt cover.
WARNING: Ensure that belt is correctly
located before fitting bolt cover.
13. Align belt to upper anchorage point. Secure with
nut. Tighten to
25 Nm. (18 lbf.ft). Fit cover.
14. Secure seat belt guide to ’B’ post.
15. Refit lower ’B’ post finisher.
76
CHASSIS AND BODY
NEW RANGE ROVER
54
REPAIR
FRONT SEAT BELT ADJUSTABLE MOUNTING
Service repair no - 76.73.26
Remove
1. Remove ’B’ post trim upper.
2. Remove 2 screws securing adjustable mounting.
Remove mounting.
Refit
3. Position adjustable mounting. Secure with
screws. Tighten to
25 Nm. (18 lbf.ft)
4. Fit ’B’ post trim upper.
SEAT BELT ADJUSTABLE MOUNTING - ’D’ POST
Service repair no - 76.73.36
Remove
1. Remove ’D’ post trim - upper.
2. Remove 2 screws securing adjustable mounting.
Remove mounting.
Refit
3. Position adjustable mounting. Secure with
screws. Tighten to
25 Nm. (18 lbf.ft)
4. Refit ’D’ post trim - upper.
CHASSIS AND BODY
55
REPAIR
REAR SEAT BELT - CENTRE
Service repair no - 76.73.20
Remove
1. Remove right hand rear seat.
See SEATS,
Repair.
2. Remove 3 screws securing squab hinge cover.
Remove cover.
3. Remove 2 bolts securing squab to cushion
assembly.
4. Remove squab from cushion assembly.
5. Remove bolt and wave washer securing stalk to
squab hinge. Remove stalk. Collect plain
washer.
6. Release beaded edge of cushion cover from
seat pan flange. Remove cushion cover/foam
assembly.
CAUTION: Take care when releasing
cover/foam from belt anchorage finisher.
76
CHASSIS AND BODY
NEW RANGE ROVER
56
REPAIR
7. Remove 3 screws securing anchorage cover to
seat pan. Remove cover in 2 pieces.
8. Remove bolt securing seat belt to seat pan.
Remove belt, collect spacer.
Refit
9. Fit seat belt to seat pan. Secure with bolt and
spacer. Tighten to
35 Nm. (26 lbf.ft)
10. Fit seat belt anchorage cover. Secure with
screws.
11. Fit cushion assembly to seat pan. Secure
beaded edge of cover to seat pan flange.
12. Fit stalk to squab hinge. Secure with bolt.
Tighten to
35 Nm. (26 lbf.ft)
13. Position seat squab to cushion assembly.
Secure with bolts. Tighten to
45 Nm. (33 lbf.ft)
14. Refit squab hinge cover. Secure with screws.
15. Refit rear seat assembly.
See SEATS, Repair.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст