Range Rover Body Repair Manual — part 30
CHASSIS AND BODY
45
REPAIR
5. Disconnect cable latch, remove glove box
assembly.
Glove Box Lid
6. Remove split pin, disengage gas strut from lid.
7. Remove 2 bolts and square nuts, remove lid
from glove box.
Refit Glove Box Lid
8. Position lid to glove box and secure with bolts
and square nuts.
9. Engage gas strut, secure with split pin.
Refit Glove Box Assembly
10. Position glove box assembly, connect lamp
multiplug. Secure cable latch.
11. Open glove box lid, align assembly to fascia.
Secure with screws.
12. Fit bolts securing hinges to fascia frame, do no
tighten.
13. Check alignment and latching of glove box lid,
adjusting hinges as necessary using central
adjusting screws.
14. Tighten screws, hinges to fascia.
15. Close glove box lid.
16. Position closing panel. Secure with scrivet
fasteners.
76
CHASSIS AND BODY
NEW RANGE ROVER
46
REPAIR
GLOVE BOX RELEASE CABLE
Service repair no - 76.52.14
NOTE: Release cables are supplied preset
and do not normally require adjustment.
Remove
1. Open glove box. Remove 5 screws securing
glove box liner to fascia.
2. Lower glove box liner. Release 2 clips to
disengage cable latch from location.
3. Remove finisher from lock.
4. Remove 2 screws securing lock and withdraw
cable assembly from fascia.
5. Pry cover from lock button.
6. Insert key into lock, turn key through 45 degrees,
remove barrel.
Refit
7. Insert barrel, turn to engage in button.
8. Remove key, fit cover to lock button.
9. Route release cable assembly into fascia.
Engage cable latch to glove box.
10. Align glove box liner to fascia, tighten screws.
11. Close glove box lid.
12. Position glove box lock to fascia, check
operation of latch.
13. If adjustment is necessary, release lock from
fascia, loosen cable lock nut, adjust outer cable
length. Tighten cable lock nut.
14. Reposition lock to fascia. Recheck operation of
latch before securing lock with screws.
15. Fit finisher to lock.
CHASSIS AND BODY
47
REPAIR
GRAB HANDLE
Service repair no - 76.58.30
Remove
1. Pull down grab handle.
2. Remove 2 grab handle retaining screw access
covers.
3. Remove 2 screws, remove grab handle.
Refit
4. Position grab handle, fit 2 retaining screws.
5. Fit 2 retaining screw access covers.
6. Release grab handle.
FRONT GRILLE
Service repair no - 76.55.03
Remove
1. Remove 6 screws securing grille.
2. Remove front grille.
Refit
3. Reverse removal procedure.
76
CHASSIS AND BODY
NEW RANGE ROVER
48
REPAIR
EXTERIOR MIRROR
Service repair no - 76.10.52
Remove
1. Release cheater panel, disconnect 2 tweeter
speaker connectors. Remove cheater panel.
2. Disconnect mirror multiplug.
3. Remove 3 screws, remove mirror.
Refit
4. Fit mirror, tighten 3 retaining screws.
5. Connect mirror multiplug.
6. Position cheater panel, connect 2 tweeter
speaker connectors, secure panel to door.
INTERIOR MIRROR
Service repair no - 76.10.51
Remove
1. Remove cover.
2. If fitted, diconnect multiplug.
3. Remove mirror from windscreen location by
pulling sharply downwards.
Refit
4. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст