Discovery (1995+): Body Repair Manual — part 25
76
CHASSIS AND BODY
38
REPAIR
SUNROOF ASSEMBLY - ELECTRICAL, FRONT
AND REAR
Service repair no - 76.82.59
Remove
Refer to sunroof components illustration J5483
1. Ensure sunroof is in normally closed position.
2. Disconnect battery negative lead.
3. Remove headlining.
See this section.
4. Disconnect electric motor wiring plug.
See this
section.
5. Remove screws and detach electric motor from
clamping frame.
6. Disconnect drain tubes from each side of
clamping frame.
7. Remove 13 fixings and remove clamping frame
from upper frame.
8. Remove upper frame assembly.
Refit
9. Position upper frame assembly into roof
aperture.
10. Locate clamping frame and reconnect drain
tubes.
11. Loosely fit screws, centralise upper frame and
clamping frame assemblies and then tighten
screws.
12. Reverse removal procedure.
CHASSIS AND BODY
39
REPAIR
SUNROOF ELECTRIC MOTORS
Service repair no - 76.82.84/85
FRONT MOTOR
Remove
1. Disconnect battery negative lead.
2. Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle A.
3. Remove switch panel from stowage pocket
panel
4. Remove interior lamp from stowage pocket
panel
5. Remove alarm ultrasonic unit.
6. Unscrew ten fixings and remove stowage pocket
from headlining.
7. Disconnect motor wiring multiplug.
8. Remove three screws and motor.
Refit
9. Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.
REAR MOTOR
Remove
1. Disconnect battery negative lead.
2. Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3. Remove headlining.
See this section.
4. Disconnect motor wiring multiplug.
5. Remove three screws and motor.
Refit
6. Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.
76
CHASSIS AND BODY
40
REPAIR
SUNROOF ELECTRIC CONTROL UNIT
Service repair no - 76.82.73
The control unit serves both front and rear sunroofs
and is sited above the front switches behind
headlining.
Remove
1. Disconnect battery negative lead.
2. Ensure sunroof is in normally closed position.
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3. Remove switch panel from stowage pocket
panel
4. Remove interior lamp from stowage pocket
panel
5. Remove alarm ultrasonic unit.
6. Unscrew ten fixings and remove stowage pocket
from headlining.
7. Disconnect electric plugs from control unit.
8. Remove two retaining screws and control unit.
Refit
9. Reverse removal procedure.
CHASSIS AND BODY
41
REPAIR
SUNROOF ASSEMBLY - MANUAL, FRONT AND
REAR
Service repair no - 76.83.01
Remove
1. Close sunroof.
2. Remove headlining.
See this section.
3. Remove screws and manual regulator from
clamping frame.
See this section.
4. Disconnect drain tubes from each side of
clamping frame.
5. Remove 13 screws and clamping frame from
upper frame.
6. Remove upper frame assembly from roof
aperture.
Refit
7. Position upper frame assembly into roof
aperture.
8. Locate clamping frame and reconnect drain
tubes.
9. Loosely fit screws, centralise upper frame and
clamping frame assemblies and then tighten
screws.
10. Reverse removal procedure.
Sunroof components
1. Glass panel
2. Capnut and washer
3. Screw
4. Upper frame assembly
5. Clamping frame assembly
6. Screw
7. Edging trim
8. Drain tube
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст