Defender 90 NAS. Manual — part 100
86
ELECTRICAL
16
REPAIR
IMMOBILIZATION (ALARM) ECU
Service repair no - 86.77.01
Remove
1. Disconnect battery negative lead.
2. Remove steering wheel. If necessary, use puller
LRT-57-014.
3. Remove instrument panel.
See INSTRUMENTS,
Repair, Instrument panel
4. Remove 2 screws securing immobilization ECU
to fascia cowl.
5. Release ECU and disconnect both multi-plugs.
6. Remove ECU.
NOTE: A new ECU must be initialised
using TestBook.
Refit
7. Reconnect multi-plugs and secure ECU to fascia
cowl.
8. Fit instrument panel.
See INSTRUMENTS,
Repair, Instrument panel
9. Fit steering wheel.
10. Reconnect battery negative lead.
INSTRUMENTS
1
REPAIR
INSTRUMENT PANEL
Service repair no - 88.20.02
Remove
1. Disconnect battery negative lead.
2. Remove 4 screws securing instrument panel to
fascia cowl.
3. Pull instrument panel away from fascia sufficent
to reach behind speedometer.
4. Disconnect instrument harness multi-plug.
5. Disconnect 2 multi-plugs from warning light
connectors.
6. Withdraw panel, complete with instruments.
Refit
7. Offer up instrument panel and connect
multi-plugs.
8. Secure instrument panel to fascia panel.
SPEEDOMETER
Service repair no - 88.30.01
Remove
1. Remove instrument panel assembly.
See
Instrument panel
2. Release tie sucuring harness and multiplug to
speedometer.
3. Disconnect multi-plug from speedometer.
4. Unscrew retaining ring and remove
speedometer.
5. Remove ’O’ ring from speedometer.
Refit
6. Fit ’O’ ring to speedometer and position
speedometer into instrument panel.
7. Fit retaining ring, align dial and tighten.
8. Connect multiplug to speedometer.
9. Secure harness and multiplug with tie.
10. Secure instrument panel to fascia cowl.
See
Instrument panel
88
INSTRUMENTS
2
REPAIR
TACHOMETER
Service repair no - 88.30.21
Remove
1. Remove instrument panel.
See Instrument
panel
2. Release illumination bulb holder and wiring
connectors from tachometer.
’-’ = BLACK
’+’ = WHITE
’2’ = RED
3. Unscrew retaining ring and remove tachometer.
4. Remove ’O’ ring from tachometer.
Refit
5. Fit ’O’ ring to tachometer and position
tachometer into instrument panel.
6. Fit retaining ring, align tachometer and tighten.
7. Fit instrument panel.
See Instrument panel
FUEL AND TEMPERATURE GAUGES
Service repair no - 88.25.26 - Fuel gauge
Service repair no - 88.25.14 - Temperature gauge
Remove
1. Remove instrument panel.
See Instrument
panel
2. Release illumination bulb holder and multiplug
from gauge.
3. Unscrew retaining ring and remove gauge, see
88M0186 .
4. Remove ’O’ ring from gauge.
Refit
5. Fit ’O’ ring to gauge and position gauge into
instrument panel.
6. Fit retaining ring, align gauge and tighten.
7. Fit instrument panel.
See Instrument panel
INSTRUMENTS
3
REPAIR
CLOCK
Service repair no - 88.15.07
Remove
1. Remove 2 screws and withdraw switch panel
from centre dash panel.
2. Release illumination bulb holder and disconnect
electrical leads from clock.
3. Press in spring retainers and remove clock from
panel.
Refit
4. Fit clock into dash panel.
5. Fit electrical leadsbulb and bulb holder.
6. Secure switch panel to centre dash panel.
WARNING LIGHT PANEL
Service repair no - 88.20.18
Remove
1. Remove 2 screws and withdraw warning light
panel.
2. Disconect both multi-plugs.
3. Disconnect illumination bulb leads.
4. Remove warning light panel.
Refit
5. Fit illumination bulb leads and multi-plugs to
warning light panel.
6. Secure warning light panel to instrument panel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст