Discovery 2. Manual — part 233
EXTERIOR FITTINGS
REPAIRS 76-2-13
Bumper assembly - rear - from 03MY
$% 76.22.15
Remove
1. Remove both rear tail lamps.
LIGHTING, REPAIRS, Lamp - tail/
2. Disconnect park distance control harness
multiplug.
3. Release rear lamp harness clips.
4. Remove 2 bolts securing bumper.
5. With assistance remove bumper.
NOTE: Do not carry out further dismantling if
component is removed for access only.
6. Remove 7 bolts and 5 screws securing closing
panel and remove panel.
M76 4566
EXTERIOR FITTINGS
76-2-14 REPAIRS
7. Disconnect 4 park distance control sensor
harness multiplugs and remove 6 clips
retaining harness.
8. Release 3 clips retaining harness and remove
harness.
9. Noting their fitted positions, release and
remove 4 park distance control sensors and
sensor housings.
Refit
1. Fit sensor housings to bumper, ensuring lugs
on housings are aligned with cut-outs in
bumper.
2. Fit and secure sensors to housings.
3. Fit harness, secure with clips and connect
multiplugs
4. Fit closing panel and secure with bolts and
screws.
5. With assistance, fit bumper assembly to body.
6. Fit bolts securing bumper and tighten to 45 Nm
(33 lbf.ft).
7. Secure rear lamp harness clips and connect
park distance control sensor harness multiplug.
8. Fit both rear tail lamps.
LIGHTING, REPAIRS, Lamp - tail/
Trim finisher - bumper - front - from 03MY
$% 76.22.19
Remove
1. Remove 5 screws securing front bumper
finisher to bumper and position the finisher
aside.
2. Release clip securing washer hose to
headlamp washer jet and disconnect the hose.
3. Remove the bumper finisher.
NOTE: Do not carry out further dismantling if
component is removed for access only.
4. Remove clip securing headlamp washer jet to
bumper finisher and remove the washer jet.
Refit
1. Fit and secure headlamp washer jet to bumper
finisher.
2. Position bumper finisher to bumper, fit washer
hose to washer jet and secure with clip.
3. Fit bumper finisher to bumper and secure with
screws.
EXTERIOR FITTINGS
REPAIRS 76-2-15
Bumper assembly - rear - up to 03MY
$% 76.22.52
Remove
1. Remove both rear tail lamps.
LIGHTING, REPAIRS, Lamp - tail/
2. Release 2 clips securing rear lamp harnesses
to rear bumper.
3. Remove 2 bolts securing rear bumper to
chassis and collect 2 plates.
4. With assistance, remove bumper assembly.
NOTE: Do not carry out further dismantling if
component is removed for access only.
5. Remove centres of 19 trim clips securing
bumper armature to bumper valance.
6. Remove outers of trim clips.
7. Remove bumper armature from bumper
valance.
8. Release clips and remove rear lamps from
bumper valance.
Refit
1. Fit rear lamps to bumper valance.
2. Fit armature to bumper valance and secure
with trim clip outers.
3. Fit centres to trim clips.
4. With assistance, fit bumper assembly to body.
5. Position plates to rear bumper.
6. Fit and tighten bolts securing rear bumper to
chassis to 45 Nm (33 lbf.ft).
7. Fit 2 clips securing rear lamp harnesses to rear
bumper.
8. Connect multiplugs to rear lamps.
EXTERIOR FITTINGS
76-2-16 REPAIRS
Side finisher - windscreen
$% 76.43.39
Remove
1. Push centres from 3 trim clips securing finisher
to 'A' post.
2. Remove trim clip outers from finisher.
3. Release finisher from 3 spring clips.
4. Remove finisher.
Refit
1. Fit finisher to 'A' post and secure with spring
clips.
2. Fit trim clip outers to finisher.
3. Fit centres to trim clips.
Grille - front - up to 03MY
$% 76.55.03
Remove
1. Remove repeater lamps.
LIGHTING, REPAIRS, Lamp - front
2. Via access hole in wheel arch liners, remove
screws securing headlamp finishers.
3. Remove headlamp finishers from grille.
4. Remove 2 screws securing lower corners of
grille.
5. Remove 3 scrivets and remove grille.
Refit
1. Fit grille and secure with scrivets and screws.
2. Fit headlamp finishers and secure with screws.
3. Fit repeater lamps.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст