Discovery 2. Manual — part 229

2. Release exterior handle control rod from latch.
3. Release and disconnect sill button lock rod

from latch.

4. Disconnect multiplug from motor.
5. Remove 3 Torx screws securing latch and

motor assembly to door.

6. Remove latch and motor assembly through

aperture in the lower section of the door.

7. Disconnect release cable from latch and

remove latch and motor assembly.

Refit

1. Connect release cable to latch.
2. Position latch and motor assembly to door. Fit

Torx screws securing latch to door and tighten
to 7 Nm (5.2 lbf.ft).

3. Connect multiplug to motor.
4. Connect exterior handle control rod to latch.
5. Connect sill button lock rod to latch.
6. Fit front door frame.

DOORS

76-1-12 REPAIRS

Latch and motor - rear door

$% 76.37.13

Remove

1. Remove rear door frame.

2. Release exterior handle control rod from latch.
3. Release sill button lock rod from door latch.
4. Disconnect multiplug from motor.
5. Remove 3 Torx screws securing latch and

motor assembly to door.

6. Remove latch and motor assembly through

lower aperture in door.

7. Open security flap on latch.
8. Disconnect release cable from latch.

Refit

1. Connect release cable to latch and close

security flap.

2. Position latch to door, fit Torx screws securing

latch to door and tighten to 7 Nm (5.2 lbf.ft).

3. Connect multiplug to motor.
4. Connect exterior handle control rod to latch.
5. Connect sill button lock rod to latch.
6. Fit rear door frame.

DOORS

REPAIRS 76-1-13

Latch and motor - tail door

$% 76.37.16

Remove

1. Remove tail door trim casing.

2. Carefully release water shedder from tail door.

3. Release and remove control rod from exterior

handle and latch.

4. Release and remove sill button lock rod.
5. Disconnect multiplug from motor.
6. Remove release cable from clip.
7. Remove 3 Torx screws securing latch and

motor assembly to door.

8. Remove door latch.
9. Disconnect release cable from latch.

Refit

1. Connect release cable to latch.
2. Position door latch and motor assembly, secure

with Torx screws and tighten to 7 Nm (5.2 lbf.ft).

3. Position control rod and connect to exterior

handle and latch.

4. Position sill button lock rod and connect to

latch.

5. Secure release cable in clip.
6. Connect multiplug to motor.
7. Fit water shedder to door.
8. Fit tail door trim casing.

Handle - exterior - rear door

$% 76.58.02

Remove

1. Remove rear door trim casing.

2. Carefully release water shedder from door.

3. Release control rod from latch.
4. Remove Torx bolt securing exterior handle to

door.

5. Remove exterior handle.
6. Remove control rod from exterior handle.

Refit

1. Fit control rod to exterior handle.
2. Position exterior handle and secure to door with

Torx bolt.

3. Connect control rod to latch.
4. Fit water shedder to door.
5. Fit rear door trim casing.

DOORS

76-1-14 REPAIRS

Handle - exterior - tail door

$% 76.58.05

Remove

1. Remove tail door trim casing.

2. Carefully release water shedder from door.

3. Remove control rod between exterior handle

and door latch.

4. Remove 2 nuts securing exterior handle to

door.

5. Remove exterior handle.

Refit

1. Position exterior handle to door. Fit nuts and

tighten to 7 Nm (5.2 lbf.ft).

2. Connect control rod to exterior handle and door

latch.

3. Fit water shedder to door.
4. Fit tail door trim casing.

Handle - exterior - front door

$% 76.58.07

Remove

1. Remove front door trim casing.

front door.

2. Carefully release water shedder from door.

3. Release control rod from latch.
4. Remove Torx bolt securing exterior handle to

door.

5. Remove exterior handle.
6. Remove control rod from exterior handle.

Refit

1. Fit control rod to exterior handle.
2. Position exterior handle to door, fit Torx bolt

and tighten to 7 Nm. (5.2 lbf.ft).

3. Connect control rod to door latch.
4. Fit water shedder to door.
5. Fit front door trim casing.