Discovery 2. Manual — part 668
SEATS
REPAIRS 76-5-23
Motor - rise and fall - front seat
$% 78.70.27
Remove
1. Remove front seat.
2. Disconnect multiplug from rise and fall motor.
3. Remove retainers from roll pins.
4. Using a suitable drift remove roll pins securing
rise and fall motor and operating lever to seat
frame.
5. Remove rise and fall motor.
Refit
1. Position and align rise and fall motor to seat
frame.
2. Fit new roll pins to secure rise and fall motor
and operating lever.
3. Fit new retainers to roll pins.
4. Connect multiplug to rise and fall motor.
5. Fit front seat.
Motor - tilt - front seat
$% 78.70.29
Remove
1. Remove front seat.
2. Disconnect multiplug from tilt motor.
3. Remove 2 retainers and 'C' clip from roll pins
securing tilt motor.
4. Using a suitable drift remove roll pins securing
tilt motor and operating lever to seat frame.
5. Remove tilt motor.
Refit
1. Position and align tilt motor to seat frame.
2. Fit new roll pins to secure motor and operating
arm.
3. Fit new retainers and 'C' clip to roll pins.
4. Connect multiplug to tilt motor.
5. Fit front seat.
SEATS
76-5-24 REPAIRS
Motor - recline
$% 78.70.34
Remove
1. Remove squab cover.
SEATS, REPAIRS, Cover - squab -
2. Disconnect recline motor multiplug.
3. Remove 2 bolts securing recline motor and
remove motor.
Refit
1. Position recline motor and ensure gear and
gear spigot are engaged.
2. Fit and tighten bolts securing recline motor to
frame.
3. Connect recline motor multiplug.
4. Fit squab cover.
SEATS, REPAIRS, Cover - squab -
Switch - electric seats
$% 78.70.88
Remove
1. Release switch from centre console.
2. Pull the connector retaining bar outwards to the
limit of its travel and carefully disconnect the
connector from the switch.
Refit
1. Connect multiplug to rear of switch and slide
the retaining bar fully home.
2. Fit switch to centre console.
SEATS
REPAIRS 76-5-25
Cover - squab - front seat
$% 78.90.08/81
Remove
1. Remove front seat.
2. Place seat on a suitable work bench.
3. Tighten arm rest adjuster fully clockwise and
remove screw cover.
4. Remove screw securing arm rest to seat and
remove arm rest.
5. Remove 2 screws securing outer edge trim
casing to seat frame.
6. Remove trim casing.
7. Release inner edge of trim casing from seat
frame.
8. Remove trim casing.
9. Position seat upside down on table.
10. Release clip securing lower edge of squab
cover to seat frame.
11. Remove 2 clips securing either end of cover to
squab frame.
12. Position seat in upright position.
13. Raise headrest to maximum height.
14. Turn both guides through 90
°
.
15. Remove headrest from seat.
16. Remove screws securing grab handles to seat
frame and remove grab handles.
SEATS
76-5-26 REPAIRS
17. Release clip securing front of cover to squab
frame.
18. Release hooks from squab frame.
19. Fold cover upwards over squab until first row of
hog rings are visible.
20. Remove first row of hog rings.
21. Fold cover upwards over squab until second
row of hog rings are visible.
22. Remove second row of hog rings.
23. Push out centres of trim clips securing stowage
pocket elastic to seat frame.
24. Remove trim clip outers.
25. Release hooks from seat frame and feed
though to front of foam.
26. Fold cover upwards until third row of hog rings
are visible.
27. Remove third row of hog rings.
28. Remove hog rings securing rear of squab
cover to seat frame.
29. Release bar from seat frame.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст