Range Rover. Manual — part 241
CHASSIS AND BODY
59
REPAIR
FRONT SEAT BELT ADJUSTABLE MOUNTING
Service repair no - 76.73.26
Remove
1. Remove ’B’ post trim upper.
2. Remove 2 screws securing adjustable mounting.
Remove mounting.
Refit
3. Position adjustable mounting. Secure with
screws. Tighten to
25 Nm. (18 lbf.ft)
4. Fit ’B’ post trim upper.
SEAT BELT ADJUSTABLE MOUNTING - ’D’ POST
Service repair no - 76.73.36
Remove
1. Remove ’D’ post trim - upper.
2. Remove 2 screws securing adjustable mounting.
Remove mounting.
Refit
3. Position adjustable mounting. Secure with
screws. Tighten to
25 Nm. (18 lbf.ft)
4. Refit ’D’ post trim - upper.
76
CHASSIS AND BODY
NEW RANGE ROVER
60
REPAIR
REAR SEAT BELT - CENTRE
Service repair no - 76.73.20
Remove
1. Remove right hand rear seat.
See SEATS,
Repair.
2. Remove 3 screws securing squab hinge cover.
Remove cover.
3. Remove 2 bolts securing squab to cushion
assembly.
4. Remove squab from cushion assembly.
5. Remove bolt and wave washer securing stalk to
squab hinge. Remove stalk. Collect plain
washer.
6. Release beaded edge of cushion cover from
seat pan flange. Remove cushion cover/foam
assembly.
CAUTION: Take care when releasing
cover/foam from belt anchorage finisher.
CHASSIS AND BODY
61
REPAIR
7. Remove 3 screws securing anchorage cover to
seat pan. Remove cover in 2 pieces.
8. Remove bolt securing seat belt to seat pan.
Remove belt, collect spacer.
Refit
9. Fit seat belt to seat pan. Secure with bolt and
spacer. Tighten to
35 Nm. (26 lbf.ft)
10. Fit seat belt anchorage cover. Secure with
screws.
11. Fit cushion assembly to seat pan. Secure
beaded edge of cover to seat pan flange.
12. Fit stalk to squab hinge. Secure with bolt.
Tighten to
35 Nm. (26 lbf.ft)
13. Position seat squab to cushion assembly.
Secure with bolts. Tighten to
45 Nm. (33 lbf.ft)
14. Refit squab hinge cover. Secure with screws.
15. Refit rear seat assembly.
See SEATS, Repair.
76
CHASSIS AND BODY
NEW RANGE ROVER
62
REPAIR
REAR SEAT BELT - LEFT HAND
Service repair no - 76.73.23
Remove
1. Remove parcel shelf support trim.
See this
section.
2. Remove ’D’ post lower trim.
See this section.
3. Remove cover and nut securing seat belt to
upper anchorage point.
4. Remove bolt securing seat belt reel.
5. Remove seat belt reel.
6. Remove left hand rear seat.
See SEATS,
Repair.
7. Remove 3 screws securing squab hinge cover.
Remove cover.
8. Remove 2 bolts securing squab to cushion
assembly.
9. Remove squab from cushion assembly.
10. Remove bolt and wave washer securing stalk to
squab hinge.
11. Remove stalk. Collect plain washer.
Refit
12. Fit stalk to squab hinge. Secure with bolt.
Tighten to
35 Nm. (26 lbf.ft)
13. Position seat squab to cushion assembly.
Secure with bolts. Tighten to
45 Nm. (33 lbf.ft)
14. Refit squab hinge cover. Secure with screws.
15. Refit rear seat assembly.
See SEATS, Repair.
16. Position belt to upper anchorage point. Secure
with nut. Tighten to
25 Nm. (18 lbf.ft). Fit
cover.
17. Position seat belt reel. Secure with bolt. Tighten
to
35 Nm. (26 lbf.ft)
18. Fit ’D’ post lower trim.
See this section.
19. Fit parcel shelf support trim.
See this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст