Range Rover. Manual — part 240
CHASSIS AND BODY
55
REPAIR
9. Release 2 clips securing trim to body and
remove trim.
Refit
10. Position trim panel to body and secure clips.
11. Fit mounting bracket to body with trim clips.
12. Feed satellite navigation and power socket wires
through correct holes, Push trim into place and
secure with trim clip.
13. Position mounting bracket behind trim and feed
mounted threads through holes in trim.
14. Position power socket bracket, feed wires
through bracket and connect socket.
15. Fit socket to bracket and secure clip and screw.
16. Position mounting plate to top of trim and
position GPS receiver to mounting plate.
17. Fit satellite navigation computer bracket to trim
and secure with nuts.
18. Fit satellite navigation trim cover and secure with
screws and trim clips.
19. Fit satellite navigation computer.
See
ELECTRICAL, Repair.
20. Fit parcel tray support.
See this section.
A,B,D and E POST TRIMS
Remove
1. Remove aperture seal from appropriate area.
2. Remove retaining screws (’A’ post lower trims)
3. Remove seat belt top mounting (’B’ and ’D’ post
upper trims)
4. Release retaining clips, remove finisher.
Refit
5. Position finisher, secure with retaining clips and
screws.
6. Fit seat belt top mounting. Tighten to
25 Nm.
(18lbf. ft)
7. Secure aperture seal.
NOTE: Illustration 76M 7128 shows the
fixing method for the A, B, D and E post
trim finishers.
1. A post upper
2. A post lower left hand
3. A post lower right hand
4. B post upper
5. B post lower
6. D post upper
7. D post lower
8. E post
76
CHASSIS AND BODY
NEW RANGE ROVER
56
REPAIR
CHASSIS AND BODY
57
REPAIR
’E’ POST - EXTERIOR TRIM
Service repair no - 76.43.
Remove
1. Open upper tailgate.
2. Remove 3 screws securing trim to ’E’ post.
3. Remove trim.
Refit
4. Position trim to ’E’ post, engage slot beneath
special washer on tailgate strut ball joint and
engage channel to rear edge of quarter glass.
5. Secure trim with screws.
6. Close tailgate.
SEAT BELT - FRONT - UP TO 99MY
Service repair no - 76.73.13
Remove
1. Remove lower ’B’ post finisher.
2. Remove cover and nut securing seat belt to
upper anchorage point.
3. Release seat belt guide from ’B’ post.
4. Move seat fully forwards.
5. Remove bolt cover. Release seat belt from lower
anchorage point on seat.
76
CHASSIS AND BODY
NEW RANGE ROVER
58
REPAIR
6. Remove bolt securing belt reel to ’B’ post,
remove belt reel.
7. Move seat fully rearwards.
8. Remove cover from seat belt stalk fixing.
Remove bolt. Collect stalk.
Refit
9. Position seat belt stalk. Secure with retaining
bolt. Tighten to
35 Nm. (26 lbf.ft). Fit bolt
cover.
10. Fit seat belt reel to ’B’ post. Secure with retaining
bolt. Tighten to
35 Nm. (26 lbf.ft)
11. Move seat fully forwards.
12. Secure seat belt to lower anchorage point. Fit
bolt cover.
WARNING: Ensure that belt is correctly
located before fitting bolt cover.
13. Align belt to upper anchorage point. Secure with
nut. Tighten to
25 Nm. (18 lbf.ft). Fit cover.
14. Secure seat belt guide to ’B’ post.
15. Refit lower ’B’ post finisher.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст