Range Rover. Manual — part 316
ELECTRICAL
5
REPAIR
ALTERNATOR - V8 - FROM 99MY
Service repair no - 86.10.02
Remove
1. Remove alternator drive belt.
See this section.
2. Remove 2 bolts securing alternator to mounting
bracket.
3. Release alternator from mounting bracket.
4. Remove nuts securing alternator cables, and
release cables.
5. Remove alternator from mounting bracket.
Refit
6. Position alternator to mounting bracket.
7. Connect alternator cables, fit nuts and tighten B+
nut to
18 Nm (13 lbf.ft) max. D+ nut to
5 Nm (3.5 lbf.ft) max. B+ and D+ are marked on
the rear of the alternator, adjacent to each cable
connection.
8. Locate alternator in mounting bracket.
9. Fit bolts and tighten to
45 Nm (33 lbf.ft).
10. Fit alternator drive belt.
See this section.
86
ELECTRICAL
NEW RANGE ROVER
6
REPAIR
ALTERNATOR - DIESEL
Service repair no - 86.10.02
Remove
1. Disconnect battery negative lead.
2. Remove alternator drive belt.
3. Release harness from terminal cover.
4. Release cover from alternator terminals.
5. Disconnect leads from alternator terminals.
6. Remove 2 bolts securing alternator to bracket.
7. Manoeuvre alternator clear of pipework. Remove
alternator.
Do not carry out further dismantling if
component is removed for access only.
8. Restrain shaft using an Allen key. Remove
pulley nut. Remove pulley.
9. Clean shaft and pulley.
10. Position pulley. Secure with nut. Tighten to
50
Nm. (37 lbf.ft)
Refit
11. Position alternator to bracket. Secure with bolts.
12. Connect leads to alternator terminals. Secure
with nuts.
13. Secure terminal cover. Engage harness sheath.
14. Fit and tension alternator drive belt.
15. Reconnect battery negative lead.
ELECTRICAL
7
REPAIR
DRIVE BELT TENSIONER - V8
Service repair no - 86.10.06
Remove
1. Disconnect battery negative lead.
2. Remove radiator cooling fan cowl.
3. Remove alternator drive belt.
See this section.
4. Remove tensioner pulley securing bolt. Remove
pulley.
5. Remove tensioner securing bolt. Remove
tensioner.
Refit
6. Ensure mating faces are clean.
7. Fit tensioner.
CAUTION: Ensure tensioner dowel is
correctly located.
8. Fit tensioner securing bolt. Tighten to
39 Nm.
(29 lbf.ft)
9. Fit tensioner pulley. Secure with bolt. Tighten to
50 Nm. (37 lbf.ft)
CAUTION: Fit special washer with raised
face towards pulley.
10. Fit alternator drive belt.
See this section.
11. Fit radiator cooling fan cowl.
12. Reconnect battery negative lead.
86
ELECTRICAL
NEW RANGE ROVER
8
REPAIR
DRIVE BELT TENSIONER - DIESEL
Service repair no - 86.10.06
Remove
1. Disconnect battery negative lead.
2. Remove drive belt.
See this section.
3. Remove bolts securing tensioner to pulley
bracket and fulcrum.
4. Remove tensioner.
CAUTION: The tensioner is an oil filled
damper which must be stored vertically.
An incorrectly stored damper must be bled
before fitment by compressing several times.
Refit
5. Reverse removal procedure.
STARTER MOTOR - V8
Service repair no - 86.60.01
Remove
1. Disconnect battery negative lead.
2. Raise the vehicle.
WARNING: Support on safety stands.
3. Remove nut securing feed wires to starter
solenoid.
4. Remove 2 feed wires from solenoid terminal.
5. Release Lucar from solenoid.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст