Range Rover. Manual — part 317
ELECTRICAL
9
REPAIR
6. Remove 2 bolts securing starter motor to engine.
NOTE: Use two extensions as illustrated to
gain access to the top bolt.
7. Remove starter motor.
Refit
8. Ensure mating faces are clean.
9. Fit starter motor.
10. Fit bolts. Tighten to
45 Nm. (33 lbf.ft)
11. Fit Lucar to starter solenoid.
12. Connect feed wires to solenoid terminal. Secure
with nut.
13. Remove stands and lower vehicle.
14. Reconnect battery negative lead.
STARTER MOTOR - V8 - 97 MY ON
Service repair no - 86.60.01
Remove
1. Disconnect battery earth lead.
2. Raise front of vehicle.
WARNING: Support on safety stands.
3. Remove gearbox RH acoustic cover.
See
CHASSIS AND BODY, Repair.
4. Remove nut securing 2 cables to starter solenoid
and position cables aside.
5. Disconnect lucar from starter solenoid.
6. Remove 2 bolts securing starter motor to engine.
86
ELECTRICAL
NEW RANGE ROVER
10
REPAIR
NOTE: Use extensions as illustrated to
gain access to top bolt.
7. Remove starter motor.
Refit
8. Clean mating faces of starter motor and engine.
9. Fit starter motor to engine.
10. Fit bolts securing starter motor to engine and
tighten to
45 Nm. (33 lbf.ft)
11. Connect Lucar to starter solenoid.
12. Connect cables to starter solenoid and secure
with nut.
13. Fit gearbox RH acoustic cover.
See CHASSIS
AND BODY, Repair.
14. Remove stand(s) and lower vehicle.
STARTER MOTOR - DIESEL
Service repair no - 86.60.01
Remove
1. Disconnect battery negative lead.
2. Remove nut and bolt securing dipstick tube.
3. Remove dipstick/tube assembly from sump.
Collect ’O’ ring and discard.
4. Remove nut and bolt securing rear support stay
to inlet manifold. Remove stay.
5. Raise the vehicle.
WARNING: Support on safety stands.
6. Remove nuts securing wires to starter solenoid
terminals. Disconnect wires.
7. Slacken lower bolt securing clutch fluid pipe
bracket to engine.
8. With assistance remove nuts and bolts securing
starter motor.
9. Move fluid pipe bracket clear, release starter
motor from dowel. Remove starter motor.
ELECTRICAL
11
REPAIR
Refit
10. Ensure mating faces are clean.
11. Position starter motor. Locate onto dowel.
12. Align fluid pipe bracket. Secure starter motor
with nuts and bolts. Tighten to
48 Nm.
(35 lbf.ft).
13. Tighten clutch fluid pipe bracket lower bolt to
86 Nm (63 lbf.ft).
INDICATOR STALK
Service repair no - 86.65.64
Remove
1. Remove steering column nacelle.
See
STEERING, Repair.
2. Disconnect multiplug from stalk.
3. Remove 2 screws securing stalk to steering
column.
4. Remove indicator stalk.
Refit
5. Reverse removal procedure.
86
ELECTRICAL
NEW RANGE ROVER
12
REPAIR
HANDBRAKE WARNING SWITCH
Service repair no - 86.65.45
Remove
1. Remove centre console.
See CHASSIS AND
BODY, Repair.
2. Disconnect 2 Lucars from warning switch.
3. Remove 2 screws securing switch. Remove
switch.
Refit
4. Reverse removal procedure.
STEERING WHEEL MOUNTED SWITCHES
Service repair no - 86.50.13 - Radio Controls
Remove
1. Remove steering wheel pad.
See STEERING,
Repair.
2. Vehicles with SRS: Remove drivers air bag
module.
See SUPPLEMENTARY RESTRAINT
SYSTEM, Repair.
3. Disconnect steering wheel switch multiplug.
4. Remove 2 screws securing multiplug to horn
unit.
5. Remove 3 screws securing printed circuit to horn
unit.
CAUTION: The 3 screws securing the
printed circuit to horn unit are not
replaceable, if damaged during removal a
new steering wheel must be fitted. Do not attempt
to use other fixings.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст