Range Rover. Manual — part 238
CHASSIS AND BODY
47
REPAIR
Refit Glove Box Lid
8. Position lid to glove box and secure with bolts
and square nuts.
9. Engage gas strut, secure with split pin.
Refit Glove Box Assembly
10. Position glove box assembly, connect lamp
multiplug. Secure cable latch.
11. Open glove box lid, align assembly to fascia.
Secure with screws.
12. Fit bolts securing hinges to fascia frame, do no
tighten.
13. Check alignment and latching of glove box lid,
adjusting hinges as necessary using central
adjusting screws.
14. Tighten screws, hinges to fascia.
15. Close glove box lid.
16. Position closing panel. Secure with scrivet
fasteners.
GLOVE BOX RELEASE CABLE
Service repair no - 76.52.14
NOTE: Release cables are supplied preset
and do not normally require adjustment.
Remove
1. Open glove box. Remove 5 screws securing
glove box liner to fascia.
2. Lower glove box liner. Release 2 clips to
disengage cable latch from location.
3. Remove finisher from lock.
76
CHASSIS AND BODY
NEW RANGE ROVER
48
REPAIR
4. Remove 2 screws securing lock and withdraw
cable assembly from fascia.
5. Pry cover from lock button.
6. Insert key into lock, turn key through 45 degrees,
remove barrel.
Refit
7. Insert barrel, turn to engage in button.
8. Remove key, fit cover to lock button.
9. Route release cable assembly into fascia.
Engage cable latch to glove box.
10. Align glove box liner to fascia, tighten screws.
11. Close glove box lid.
12. Position glove box lock to fascia, check
operation of latch.
13. If adjustment is necessary, release lock from
fascia, loosen cable lock nut, adjust outer cable
length. Tighten cable lock nut.
14. Reposition lock to fascia. Recheck operation of
latch before securing lock with screws.
15. Fit finisher to lock.
GRAB HANDLE
Service repair no - 76.58.30
Remove
1. Pull down grab handle.
2. Remove 2 grab handle retaining screw access
covers.
3. Remove 2 screws, remove grab handle.
Refit
4. Position grab handle, fit 2 retaining screws.
5. Fit 2 retaining screw access covers.
6. Release grab handle.
CHASSIS AND BODY
49
REPAIR
FRONT GRILLE
Service repair no - 76.55.03
Remove
1. Remove 6 screws securing grille.
2. Remove front grille.
Refit
3. Reverse removal procedure.
EXTERIOR MIRROR
Service repair no - 76.10.52
Remove
1. Release cheater panel, disconnect 2 tweeter
speaker connectors. Remove cheater panel.
2. Disconnect mirror multiplug.
3. Remove 3 screws, remove mirror.
Refit
4. Fit mirror, tighten 3 retaining screws.
5. Connect mirror multiplug.
6. Position cheater panel, connect 2 tweeter
speaker connectors, secure panel to door.
76
CHASSIS AND BODY
NEW RANGE ROVER
50
REPAIR
INTERIOR MIRROR
Service repair no - 76.10.51
Remove
1. Remove cover.
2. If fitted, disconnect multiplug.
3. Remove mirror from windscreen location by
pulling sharply downwards.
Refit
4. Reverse removal procedure.
INTERIOR MIRROR - ELECTRONIC DIP - FROM
2000MY
Service repair no - 76.10.53
Remove
1. Release 2 clips securing interior mirror cover to
interior mirror and remove cover.
2. Disconnect multiplug from interior mirror.
3. Rotate interior mirror to release from bracket and
remove mirror.
Refit
4. Position mirror to bracket and rotate to secure.
5. Connect multiplug to interior mirror.
6. Fit interior mirror cover to interior mirror and
secure clips.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст