Range Rover. Manual — part 237
CHASSIS AND BODY
43
REPAIR
TRIM CASING - REAR DOOR
Service repair no - 76.34.04
Remove
1. Remove screw securing remote handle
escutcheon and remove escutcheon.
2. Remove 2 screws securing trim casing to door.
3. Release 11 door trim casing retaining studs.
4. Disconnect rear door speaker and remove door
trim.
5. Remove 11 trim casing retaining studs from trim
casing.
76
CHASSIS AND BODY
NEW RANGE ROVER
44
REPAIR
6. Remove 4 speed nuts securing speaker to trim
casing and remove speaker.
7. Remove 4 Torx bolts securing speaker grille to
trim casing and remove grille.
8. Remove 4 speed nuts securing arm rest to trim
casing and remove arm rest.
9. Remove 3 nuts securing door trim finisher to
door trim and remove finisher.
10. Remove screw securing door lock button
escutcheon to door trim and remove
escutcheon.
Refit
11. Fit door lock button escutcheon to door trim and
secure with screw.
12. Fit door trim finisher to door trim and secure with
nuts.
13. Fit arm rest to door trim and secure with speed
nuts.
14. Fit speaker grille to door trim and secure with
Torx bolts.
15. Fit speaker to trim casing and secure with speed
nuts.
16. Fit trim casing retaining studs.
17. Position door trim to rear door and connect
multiplug to speaker.
18. Fit door trim to rear door and secure with screws
and retaining studs.
19. Fit door handle escutcheon to door and secure
with screw.
CHASSIS AND BODY
45
REPAIR
OUTER WAIST SEAL - REAR DOOR
Service repair no - 76.31.54
Remove
1. Remove screw securing seal finisher to forward
edge of door.
2. Release seal finisher from clip at rear edge of
door.
3. Remove seal and finisher assembly.
4. Remove screw and securing clip.
Refit
5. Fit clip to door, secure with screw.
6. Fit seal and finisher assembly to door. Align at
forward edge, secure with screw.
RUBBING STRIPS & DOOR FINISHERS
Remove
CAUTION: When removing exterior trim,
NEVER lever directly against body panels.
Use an approved trim fork. Protect body
panel with suitable material, such as fabric
covered hardboard.
Rubbing Strip - Front Fender
1. Remove relevant wheel arch liner.
See this
section.
2. Remove nut securing forward edge of rubbing
strip.
3. Remove rubbing strip from single clip.
Rubbing Strip - Rear Quarter Panel
4. Release 5 clips securing rubbing strip. Remove
strip.
NOTE: Rearmost clip is unique.
Rubbing Strips - Front & Rear Doors
5. Remove nut securing rear of rubbing strip.
6. Front Door Rubbing Strip: Release 5 clips
securing rubbing strip.
7. Rear Door Rubbing Strip: Release 3 clips
securing rubbing strip.
8. Remove rubbing strips.
Lower Door Finishers
9. Remove screw securing rear of finisher.
10. Front Door Finisher: Release 5 clips securing
rubbing strip.
11. Rear Door Finisher: Release 3 clips securing
rubbing strip.
12. Remove finishers.
Refit
13. Reverse removal procedure.
76
CHASSIS AND BODY
NEW RANGE ROVER
46
REPAIR
GLOVE BOX AND LID
Service repair no - 76.52.03 - Glove Box
Service repair no - 76.52.02 - Glove Box Lid
Service repair no - 76.52.13 - Glove Box Lid - Align
Remove
1. Remove centre screw from 2 scrivet fasteners.
Release closing panel for access to glove box
hinge fixings. Collect outer parts of fasteners
from closing panel.
2. Remove 2 bolts securing glove box hinges to
fascia frame.
3. Open glove box lid, remove 5 screws securing
glove box. Release glove box from fascia.
4. Disconnect glove box lamp multiplug.
5. Disconnect cable latch, remove glove box
assembly.
Glove Box Lid
6. Remove split pin, disengage gas strut from lid.
7. Remove 2 bolts and square nuts, remove lid
from glove box.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст