Range Rover. Manual — part 54
LAND ROVER V8
35
REPAIR
ENGINE MOUNTINGS - from 99MY
Service repair no - 12.45.11 - LH
Service repair no - 12.45.12 - RH
Remove
1. With assistance, release bonnet struts and retain
bonnet in vertical position with stay clips.
2. Release fixings and remove battery cover.
3. Disconnect battery earth lead.
4. Remove bolt securing screen washer filler tube.
5. Release 2 clips and remove cooling fan cowl.
6. Remove ties securing harness to support
bracket at rear of engine and move harness
clear of bracket.
7. Remove bolt securing harness support bracket
and remove bracket.
8. Right hand engine mounting: Fit suitable lifting
eye to alternator fixing bolt.
9. RHD - Right hand engine mounting: Remove
steering column intermediate shaft.
See
STEERING, Repair.
10. Raise vehicle on 4 post ramp.
11. Remove and discard 4 nuts securing engine
mounting.
12. Connect hoist to lifting eye and raise relevant
side of engine.
13. Remove engine mounting.
12
ENGINE
NEW RANGE ROVER
36
REPAIR
Refit
14. Fit engine mounting. Ensure domed head of
centre bolt faces towards chassis.
15. Carefully lower engine onto mounting and
disconnect hoist.
16. Fit new engine mounting nuts and tighten to
45
Nm (33 lbf.ft).
17. Lower vehicle.
18. RHD - Right hand engine mounting: Fit
steering column intermediate shaft
See
STEERING, Repair.
19. Right hand mounting: Remove lifting eye from
alternator fixing bolt.
20. Fit harness support bracket and secure with bolt.
21. Lay harness onto bracket and secure with cable
ties.
22. Fit cooling fan cowl and secure with clips.
23. Fit bolt to secure screen washer reservoir filler
tube.
24. Connect battery earth lead.
25. Fit battery cover and secure with fixings.
26. With assistance, release bonnet stay clips and
engage bonnet struts.
REAR ENGINE MOUNTING
Service repair no - 12.45.08
Remove
1. Raise vehicle on 4 post ramp.
2. Support transmission using a suitable stand.
3. Remove 4 nuts and 2 bolts securing mounting to
crossmember and discard nuts.
4. Remove transmission snubber bar.
5. If applicable, remove 2 bolts securing rear of
gearbox side acoustic covers to crossmember.
LAND ROVER V8
37
REPAIR
6. Remove 3 of 4 nuts and bolts securing each side
of crossmember to chassis.
7. With assistance, remove remaining bolt securing
crossmember and remove crossmember.
8. Remove 4 bolts securing mounting to gearbox.
9. Remove mounting assembly.
Refit
CAUTION: Ensure all under body wax is
removed from mating surfaces of fixings
before fitting.
10. Fit mounting to gearbox, fit bolts and tighten to
45 Nm (33 lbf.ft)
11. Using assistance, fit crossmember to chassis.
12. Fit nuts and bolts and tighten to
45 Nm (33
lbf.ft)
13. Fit transmission snubber bar.
14. Fit NEW flange nuts and bolts securing
transmission mount to crossmember and tighten
to
45 Nm (33 lbf.ft)
15. Remove transmission stand.
16. If applicable, align rear of side acoustic covers to
crossmember and secure with bolts.
12
ENGINE
NEW RANGE ROVER
38
REPAIR
OIL FILTER
Service repair no - 12.60.04
Remove
1. Raise front of vehicle.
WARNING: Support on safety stands.
2. Remove engine acoustic cover (if applicable).
See CHASSIS AND BODY, Repair.
3. Position drain tray to catch spillage.
4. Remove oil filter cartridge.
Refit
5. Clean mating face of oil pump.
6. Lubricate oil filter seal with clean engine oil.
7. Fit oil filter and tighten until rubber seal contacts
machined face. Tighten a further half turn by
hand.
CAUTION: DO NOT overtighten oil filter.
8. Run engine to allow oil to fill filter.
9. Stop engine, check and top up oil level.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information.
10. Fit engine acoustic cover (if applicable).
See
CHASSIS AND BODY, Repair.
11. Remove stand(s) and lower vehicle.
OIL COOLER
Service repair no - 12.60.68
Remove
1. Disconnect battery negative lead.
2. Raise the vehicle.
WARNING: Support on safety stands.
3. Remove front grille.
See CHASSIS AND BODY,
Repair.
4. Release 2 clips securing bonnet release cable to
bonnet platform.
5. Remove 4 bolts securing bonnet platform.
Remove platform.
6. Remove 4 bolts from condenser mounting
brackets. Collect 2 brackets.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст