Range Rover. Manual — part 229
CHASSIS AND BODY
11
REPAIR
5. Remove 2 bumper bolt access plugs from
bumper valance. Remove bolts.
6. With assistance remove bumper assembly.
Do not carry out further dismantling if
component is removed for access only.
7. Remove 8 studs and 6 clips securing extensions
spoiler. Remove extension.
8. Remove 8 screws securing fog lamps. Remove
lamps.
9. Remove 8 bolts securing bumper end brackets
to bumper. Remove brackets.
WARNING: If front bumper is damaged due
to impact, the impact cans must be
inspected. There must be no visible
deformation. The overall length must be 188.25
mm æ 0.5 mm. Replace the impact cans if
necessary.
Refit
10. Fit end brackets and secure with bolts. Fit fog
lamps and secure with screws.
11. Fit extension and secure with clips and studs.
12. With assistance fit bumper assembly, tighten
bolts to
70Nm. (52 lbf.ft)
13. Fit bolt access plugs.
14. Align end brackets, tighten bolts and secure
bumper end clips.
15. Connect fog lamp multiplugs and breather
hoses, fit battery cover.
16. Remove safety stands. Lower vehicle.
76
CHASSIS AND BODY
NEW RANGE ROVER
12
REPAIR
EXTENSION SPOILER FRONT BUMPER
Service repair no - 76.22.78
Remove
1. Raise the vehicle.
WARNING: Support on safety stands.
2. Remove 8 studs and 6 clips securing spoiler to
front bumper.
3. Remove spoiler halves.
Refit
4. Fit spoiler halves to bumper. Secure with clips
and studs.
5. Remove safety stands. Lower vehicle.
REAR BUMPER VALANCE
Service repair no - 76.22.74
Remove
1. Raise the vehicle.
WARNING: Support on safety stands.
2. Remove rear road wheels.
3. Remove 3 screws securing each mud flap.
Remove mud flaps.
4. Remove 2 screws securing each wheel arch
liner extension panel to rear bumper/chassis.
5. Remove 2 wheel arch liner extension panels.
6. Release 2 clips securing bumper ends to
mounting brackets.
CHASSIS AND BODY
13
REPAIR
7. Disconnect 3 towing harness multiplugs.
8. Remove 2 mounting bolt covers.
9. Remove 2 bolts securing bumper to chassis.
10. With assistance, release bumper ends from
brackets. Remove bumper.
Refit
11. With assistance, position bumper. Engage nylon
end supports to brackets.
12. If necessary, slacken bolts securing end support
brackets. Align bumper to body. Tighten to
29 Nm. (22 lbf.ft)
13. Fit bumper mounting bolts. Tighten to
70 Nm.
(52 lbf.ft)
14. Fit bolt covers.
15. Secure bumper end clips.
16. Connect towing harness multiplugs.
17. Position wheel arch liner extensions. Secure with
screws.
18. Position mud flaps. Secure with screws.
19. Fit road wheels. Tighten to
108 Nm. (80 lbf.ft)
20. Remove safety stands. Lower vehicle.
FASCIA ASSEMBLY
Service repair no - 76.46.23/99
WARNING: The fascia assembly houses
the heater distribution unit, blower
assemblies and air conditioning
evaporator. Assistance is essential during
removal and refit procedures.
CAUTION: When removed from the
vehicle, the fascia should be placed on a
soft covered work surface, supported on
suitable wooden blocks.
Remove
1. Vehicles with SRS only: Remove battery.
See
ELECTRICAL, Repair.
2. Vehicles without SRS: Disconnect battery
negative lead.
3. Drain cooling system.
See COOLING SYSTEM,
Repair.
4. Loosen hose clips, disconnect hoses from
heater pipes.
5. Remove centre console.
See this section.
6. Remove steering column.
See STEERING,
Repair.
7. Remove wiper motor and linkage.
See WIPERS
AND WASHERS, Repair.
8. Disconnect passenger side heated front screen
multiplug. Release multiplug from clip.
76
CHASSIS AND BODY
NEW RANGE ROVER
14
REPAIR
9. Remove 6 bolts, remove remaining scuttle side
panel.
10. Remove heater intake pollen filters.
11. Remove 8 screws securing each pollen filter
housing. Remove both housings.
12. Remove radio.
See ELECTRICAL, Repair.
13. Release door aperture seal adjacent to ’A’ post
lower trim panels.
14. Driver’s side - LHD automatic vehicles only:
Remove 3 bolts securing foot rest through ’A’
post lower trim, remove foot rest.
15. Remove screw securing each ’A’ post lower trim
panel, release from single sprag clip, remove
both trim panels.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст