Range Rover. Manual — part 339
INSTRUMENTS
3
REPAIR
COOLANT TEMPERATURE SENSOR - V8 - UP TO
99MY
Service repair no - 88.25.20
Remove
1. Partially drain cooling system.
See COOLING
SYSTEM, Repair.
2. Disconnect coolant temperature sensor.
3. Position rag around sensor to catch spillage.
4. Remove sensor.
Refit
5. Ensure sensor seat in manifold is clean.
6. Coat sensor threads with Loctite 577.
7. Fit sensor. Tighten to
10 Nm. (7 lbf.ft)
8. Connect sensor.
9. Refill cooling system.
See COOLING SYSTEM,
Repair.
10. Run engine to normal operating temperature.
Check for leaks around sensor.
COOLANT TEMPERATURE SENSOR - DIESEL
Service repair no - 88.25.20
Remove
1. Partially drain cooling system.
See COOLING
SYSTEM, Repair.
2. Disconnect coolant temperature sensor
multiplug.
3. Remove sensor using a deep 19mm socket with
sufficient clearance for connector. Collect
sealing washer and discard.
Refit
4. Ensure sensor seat in cylinder head is clean.
5. Using a new sealing washer, fit sensor. Tighten
to
20 Nm. (15 lbf.ft)
6. Connect multiplug to sensor.
7. Refill cooling system.
See COOLING SYSTEM,
Repair.
8. Run engine to normal operating temperature.
Check for leaks around sensor.
88
INSTRUMENTS
NEW RANGE ROVER
4
REPAIR
INSTRUMENT PACK
Service repair no - 88.20.01
CAUTION: If vehicle has SRS fitted, both
battery terminals must be disconnected
(negative lead first) prior to removing
instrument pack.
1. Adjust steering column to fully extended/lowered
position.
2. Remove instrument pack binnacle.
See this
section.
3. Disconnect instrument pack multiplugs.
4. Remove 4 screws securing instrument pack to
fascia.
5. Remove instrument pack.
Refit
6. Reverse removal procedure.
FUEL TANK SENDER UNIT
Service repair no - 88.25.32
Remove
1. Remove fuel tank.
See FUEL SYSTEM, Repair.
2. Disconnect 2 sender unit lucars. (1large 1 small
)difficult to disconnect.
3. Carefully release 4 clips around fuel pump
housing, lower housing disengage pump from
mounting.
INSTRUMENTS
5
REPAIR
4. Carefully pivot the pump assembly, enabling
access past fuel pipe to pozidrive screw
retaining sender unit.
5. Remove 1 pozidrive screw from sender unit and
move sender aside.
Refit
6. Fit sender unit to mounting on fuel pump
assembly,locate and tighten pozidrive screw
7. Align fuel pump with lugs inside fuel pump
housing.
8. Align housing male and female connectors with
main body, carefully push fully home.
9. Fit sender unit lucar connections
10. Fit Fuel Tank
See FUEL SYSTEM, Repair.
FUEL TANK SENDER UNIT - ADVANCED EVAPS
Service repair no - 88.25.32
Remove
1. Remove fuel tank.
See FUEL SYSTEM, Repair.
2. Carefully release 3 clips retaining fuel gauge
tank unit rubber foot and move aside.
3. Release 2 lucar connections from top of fuel tank
unit, difficult to remove.
4. Carefully slide sender unit toward filter until
bracket clears main assembly then move aside.
88
INSTRUMENTS
NEW RANGE ROVER
6
REPAIR
Refit
5. Fit sender unit bracket to slots in main assembly
and press home.
6. Align clips and fit rubber foot to base of main
assembly.
7. Fit sender lucar connections to top of tank unit,
ensure wires pass through centre ring. Connect
black sender wire to red and blue sender wire to
black.
8. Fit fuel tank
See FUEL SYSTEM, Repair.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст