Range Rover. Manual — part 188
ELECTRONIC AIR SUSPENSION
13
REPAIR
HEIGHT SENSOR - 97 MY ON
Service repair no - 60.36.01
Remove
WARNING: Ensure air suspension is made
safe before commencing work. Chassis
may otherwise lower onto axle bump stops
during repair.
1. Raise front of chassis and position LRT-60-003
between bump stop and axle.
2. Lower chassis onto LRT-60-003.
3. Raise front of vehicle.
WARNING: Support on safety stands.
4. Remove 2 bolts securing heat shield to height
sensor.
5. Remove heat shield.
6. Remove nut securing height sensor lever arm to
radius arm.
7. Release sensor lever arm from radius arm.
8. Remove 2 bolts securing height sensor to
chassis.
9. Collect heat shield mounting bracket and 2
washers.
10. Position height sensor cover to gain access to
height sensor multiplug.
11. Disconnect multiplug and remove height sensor
assembly.
12. Remove cover from height sensor.
Refit
13. Fit cover to height sensor.
14. Fit bolts and washers to height sensor assembly.
15. Position height sensor to chassis and connect
multiplug.
16. Position heat shield bracket, fit height sensor
assembly and tighten bolts to
6 Nm. (4 lbf.ft) .
17. Engage sensor lever arm to radius arm, fit nut
and tighten to
8 Nm (6 lbf.ft) .
18. Position heat shield to bracket, fit bolts and
tighten to
6 Nm (4 lbf.ft) .
19. Remove stand(s) and lower vehicle.
20. Raise chassis and remove LRT-60-003.
21. Lower chassis.
22. Recalibrate system using TestBook if a new
sensor has been fitted.
60
FRONT SUSPENSION
NEW RANGE ROVER
14
REPAIR
DRIVE SHAFT AND HUB ASSEMBLY
Service repair no - 60.25.01
Remove
NOTE: This procedure gives removal
instructions for the drive shaft and oil seal,
plus the hub, bearing and drive flange
assembly.
1. Remove centre cap from front wheel, release
stake from drive shaft nut. Slacken nut.
NOTE: If the hub and drive shaft are to be
removed as an assembly, it is not
necessary to slacken the drive shaft nut.
2. Raise the vehicle.
WARNING: Support on safety stands.
3. Remove brake disc shield.
See BRAKES,
Repair.
4. Release ABS sensor harness from brackets on
hub and axle.
5. Release sensor from hub.
6. Remove sensor bush.
7. Remove 4 bolts securing hub to carrier.
ELECTRONIC AIR SUSPENSION
15
REPAIR
8. Release hub from carrier. Remove hub and drive
shaft assembly.
9. Remove drive shaft nut. Remove shaft assembly
from hub.
10. Remove drive shaft seal from axle casing.
Refit
11. Clean ABS sensor and location. Clean drive
shaft and its seal location. Clean hub bearing
carrier and its location in hub.
12. Lubricate oil seal lip and its running surface on
drive shaft.
13. Fit oil seal to axle case, using service tool
LRT-51-012.
14. Apply a 3mm band of Loctite (grade 648) to hub
flange spline.
15. Fit drive shaft to hub. Fit stake nut, do not
tighten.
16. Fit hub and drive shaft assembly. Fit bolts.
Tighten to
135 Nm (100lbf.ft)
17. Lightly grease ABS sensor and bush, using the
correct silicone grease.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.
18. Fit ABS sensor bush.
19. Fit ABS sensor fully into bush, secure lead to
brackets.
20. Fit brake disc shield.
See BRAKES, Repair.
21. Tighten drive shaft nut to
260 Nm. (192 lbf.ft)
22. Stake the nut.
23. Fit road wheel centre.
24. Remove safety stands. Lower vehicle.
60
FRONT SUSPENSION
NEW RANGE ROVER
16
REPAIR
ANTI-ROLL BAR LINK
Service repair no - 60.10.02
Remove
1. Raise the vehicle.
WARNING: Support on safety stands.
2. Remove nuts securing link to chassis and
anti-roll bar.
3. Remove link.
Refit
4. Fit link to anti-roll bar and chassis.
5. Fit securing nuts. Tighten to
125 Nm. (92 lbf.ft)
6. Remove safety stands. Lower vehicle.
PANHARD ROD AND BUSHES
Service repair no - 60.10.10. Panhard rod
Service repair no - 60.10.07. Bushes
Remove
1. Raise the vehicle.
WARNING: Support on safety stands.
2. Remove nut and bolt securing panhard rod to
chassis.
3. Remove locking plate screw, locking plate and
bolt securing panhard rod to axle.
4. Remove panhard rod.
5. Press out bushes from rod.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст