Frelander 2. Manual — part 387
8.
9.
CAUTION: Before disconnecting or removing the
components, make sure the area around the joint faces
and connections are clean. Plug open connections to
prevent contamination.
9.
10.
CAUTION: Before disconnecting or removing
the components, make sure the area around the joint
faces and connections are clean. Plug open connections
to prevent contamination.
10.
Installation
Apply anti-seize compound to the sensor and pipe union thread.
Refer to:
Specifications
(303-08B Engine Emission Control - TD4 2.2L
Diesel, Specifications).
1.
Install the temperature sensor.
Torque: 35 Nm
2.
Install the pressure sensing pipes.
Torque: 25 Nm
3.
Install the pipe clamp.
Torque: 10 Nm
4.
5.
WARNING: Make sure that new nuts are installed.
CAUTION: Make sure that the mating faces are clean and free
of foreign material.
• NOTE: Install a new gasket.
Install the diesel particulate filter.
Torque: 25 Nm
5.
6.
CAUTION: Make sure that the wiring harnesses are correctly
located.
Connect the temperature sensor electrical connector.
6.
7. CAUTIONS:
Make sure that the installation marks are aligned.
Secure the high pressure hose with a clip.
Connect the sensor hoses.
7.
Install the exhaust system.
Refer to:
Exhaust System
(309-00A Exhaust System - I6 3.2L Petrol,
Removal and Installation).
8.
Install the engine undershield.
Refer to:
Engine Undershield
(501-02 Front End Body Panels,
Removal and Installation).
9.
Exhaust System - TD4 2.2L Diesel - Diesel Particulate Filter (DPF)
Differential Pressure Sensor
Removal and Installation
Removal
WARNING: Observe due care when working near a hot exhaust system.
• NOTE: Removal steps in this procedure may contain installation details.
1.
WARNING: Make sure to support the vehicle with axle
stands.
Raise and support the vehicle.
1.
Remove the engine undershield.
Refer to:
Engine Undershield
(501-02 Front End Body Panels,
Removal and Installation).
2.
3. CAUTIONS:
Make sure that these components are installed to
the noted removal position.
Always plug any open connections to prevent
contamination.
Torque: 6 Nm
3.
Installation
To install, reverse the removal procedure.
1.
Fuel System - General Information - Fuel Tank Draining
General Procedures
• W ARNINGS:
Place the vehicle in a well ventilated, quarantined area and arrange ' No Smoking/Petrol Fumes' signs about the
vehicle.
Do not carry or operate cellular phones when working on or near any fuel related components. Highly flammable
vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related
components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in
personal injury.
The spilling of fuel is unavoidable during this operation. Ensure that all necessary precautions are taken to prevent
fire and explosion.
CAUTION: Before disconnecting or removing components, ensure the area around the joint faces and connections are
clean. Plug open connections to prevent contamination.
• NOTE: It is possible that up to 18 litres of fuel may be left in the tank after draining.
Open the fuel filler door and remove the cap.
1.
Disconnect the battery ground cable.
Refer to:
Specifications
(414-01 Battery, Mounting and Cables,
Specifications).
2.
Connect the fuel tank drain equipment ground cable to the vehicle.
3.
4.
WARNING: Fuel may still be present in the fuel tank after
draining.
Remove the fuel from the fuel tank, via the filler neck, using the fuel
tank draining equipment. Follow the manufacturer's operating
instructions.
4.
To install, reverse the removal procedure.
5.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст