Range Rover Classic. Manual — part 187
86
ELECTRICAL
36
REPAIR
A.C. GENERATOR HEAT SHIELD
Remove
1. Disconnect battery negative lead.
2. Remove fixing screw.
3. Remove nut from A.C. generator rear mounting
bolt, remove heat shield.
Refit
4. Reverse removal procedure.
HIGH LEVEL STOP LAMP
Service repair no - 86.41.35
Includes bulb renewal
Service repair no - 86.41.34
Remove
1. Disconnect battery negative lead.
2. Remove two cover retaining screws. Remove
cover.
3. Disconnect electrical leads to bulb holder.
Remove bulbholder and bulb by twisting anti-
clockwise.
4. Remove two screws, mounting plate to stop
lamp.
5. Observe position of stop lamp on rear screen.
Carefully release tabs on stop lamp from rear
screen mountings.
6. Remove stop lamp.
7. Renew bulb if necessary.
Refit
8. Reverse removal procedure.
ELECTRICAL
37
REPAIR
ALARM HORN
Service repair no - 86.77.10
Remove
1. Remove decker panel.
See CHASSIS AND
BODY, Repair, Decker Panel
2. Disconnect two Lucar connectors.
3. Remove single nut securing horn.
4. Remove horn.
Refit
5. Reverse removal procedure.
GEAR SELECTOR-INTERLOCK
Interlock solenoid
Remove
1. Disconnect battery negative lead.
2. Remove gear selector head and illumination
panel.
See CHASSIS AND BODY, Repair,
Centre Console
3. Disconnect electrical multiplug.
4. Remove screws and lift gear selector
mechanism above housing.
5. Remove screws from microswitch support
bracket.
6. Remove screws and separate side cover from
housing.
7. Disconnect wiring solenoid to multiplug.
8. Remove circlip and retainer plate.
9. Remove clip and centre sleeve.
10. Refit clip into groove on spindle and lever
against it to remove solenoid from housing.
86
ELECTRICAL
38
REPAIR
Refit
11. Fit solenoid with wiring positioned into side cover
recess.
12. Fit sleeve and new clip.
13. Fit retaining plate and circlip.
14. Connect wiring to multiplug.
15. Apply sealant and fit side cover to housing. Use
Silcoset 152 sealant or equivalent.
16. Grease all moving parts of gear selector
mechanism. Use Rocol E1A or equivalent
grease.
17. Reverse instructions 1 to 5.
Interlock microswitch onto castellated plate.
Remove
1. Disconnect battery negative lead.
2. Remove gear selector head and illumination
panel.
See CHASSIS AND BODY, Repair,
Centre Console
3. Disconnect electrical multiplug.
4. Remove screws and lift gear selector
mechanism above housing.
5. Remove screws from microswitch support
bracket.
6. Remove screws and separate side cover from
housing.
7. Disconnect wiring microswitch to multiplug.
8. Remove 3 clips as shown.
9. Slide trunnion forward and remove gear selector
arm.
ELECTRICAL
39
REPAIR
10. Remove bolts securing coxcomb.
11. Remove microswitch retaining clip and
microswitch.
Refit
12. Reverse removal procedure. correctly
positioning microswitch.
13. Apply Loctite 242E to castellated plate bolts and
tighten to 9Nm .
14. Grease all moving parts of gear selector
mechanism. Use Rocol E1A or equivalent
grease.
15. Apply Silcoset 152 sealant or equivalent and fit
side cover to housing.
Interlock microswitch onto side cover
Remove
1. Disconnect battery negative lead.
2. Remove gear selector head and illumination
panel.
See Automatic Gear Selector-Panel
Bulb
3. Disconnect electrical multiplug.
4. Remove screws from microswitch support
bracket.
5. Disconnect wiring microswitch to multiplug.
Refit
6. Reverse removal procedure. Correctly
positioning microswitch.
7. Grease all moving parts of gear selector
mechanism. Use Rocol E1A or equivalent
grease.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст