Jeep Grand Cherokee WK. Manual — part 1254
10. Install the lower clevis bolts and tighten to 169
N·m (125 ft. lbs.).
11. Install the knuckles (1) and install the halfshaft nut
(3). (if equipped)
12. Tighten the halfshaft nut (3) to 251 N·m (185 ft.
lbs.). (if equipped)
13. Install the lower ball joint into the knuckle.
14. Install the lower ball joint nut (4) and tighten the
nut to 81 N·m (60 ft. lbs.).
15. Install the upper ball joint into the knuckle.
16. Install the upper ball joint nut (2). Tighten the nut
to 81 N·m (60 ft. lbs.).
17. Install the outer tie rod end into the steering
knuckle.
18. Tighten the ball stud nut (5) on the ball stud to 75
N·m (55 ft. lbs.).
13 - 32
FRAME & BUMPERS
WK
19. Connect the speed sensor electrical connectors
(2) and fasten the harness support clips (1) fully.
20. Install the rotors. (Refer to 5 - BRAKES/HYDRAU-
LIC/MECHANICAL/ROTORS - INSTALLATION -
FRONT DISC BRAKE ROTOR)
21. Check and fill the front differential as necessary.
(Refer
to
LUBRICATION
&
MAINTENANCE/
FLUID CAPACITIES - SPECIFICATIONS)
22. Install the front skid plates. (Refer to 13 - FRAME
&
BUMPERS/FRAME/FRONT
SKID
PLATE
-
INSTALLATION)
23. Check and adjust front wheel alignment as neces-
sary. (Refer to 2 - SUSPENSION/WHEEL ALIGN-
MENT
-
STANDARD
PROCEDURE
-
COMPLETE)
CROSSMEMBER-REAR/TRANSMISSION
REMOVAL
1. Remove the skid plate. (Refer to 13 - FRAME &
BUMPERS/FRAME/SKID
PLATE-TRANSFER
CASE - REMOVAL)
2. Support the transmission with a suitable lifting
device.
3. Remove the four transmission mount bolts (1).
4. Remove the eight crossmember bolts (2) and
remove the crossmember.
INSTALLATION
1. Install the crossmember and install the eight cross-
member bolts (2).
2. Tighten the crossmember bolts to 54 N·m (40 ft.
lbs.).
3. Remove the lifting device.
4. Install the four transmission mount bolts (1) and
tighten to 54 N·m (40 ft. lbs.).
5. Install the skid plate. (Refer to 13 - FRAME &
BUMPERS/FRAME/SKID
PLATE-TRANSFER
CASE - INSTALLATION)
WK
FRAME & BUMPERS
13 - 33
HOOK-FRONT TOW
REMOVAL
1. Remove the nuts (2) and remove the tow hook (1).
Stud Plates
1. Remove the front fascia. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/FRONT
FASCIA
-
REMOVAL)
2. Release the clip fasteners and remove the stud
plates (1 & 2).
13 - 34
FRAME & BUMPERS
WK
INSTALLATION
Stud Plates
1. Install the stud plates (1 & 2) through the holes in
the front bumper beam.
1. Install the tow hook (1) and install the nuts (2).
2. Tighten the nuts to 68 N·m (50 ft. lbs.).
3. Install the front fascia. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/FRONT FASCIA - INSTAL-
LATION)
WK
FRAME & BUMPERS
13 - 35
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст