Jeep Liberty KJ. Manual — part 1341
INSTALLATION
1. If sunroof was open when drive motor was
removed, carefully move glass panel into closed
position and remove glass panel. (Refer to 23 -
BODY/SUNROOF/GLASS PANEL - REMOVAL)
2. Set lifter arm timing by manually sliding the mech-
anisms (1) in the track until timing holes in the trol-
lies are aligned with the timing holes in the lifter
arm cams (2) and insert pins (3) into the mecha-
nisms to hold mechanisms in closed position.
3. Place motor (3) into position and install screws (4)
attaching motor to bracket (2).
4. Tighten the screws (4) to 3 N·m (26 in. lbs.).
5. If sunroof glass panel was removed previously,
remove the timing pins and install the sunroof glass
panel. (Refer to 23 - BODY/SUNROOF/GLASS
PANEL - INSTALLATION)
6. Temporarily install sunroof switch and perform the
sunroof motor teach procedure. (Refer to 23 -
BODY/SUNROOF/DRIVE MOTOR - STANDARD
PROCEDURE - TEACH PROCEDURE)
7. Test sunroof operation, adjust glass as necessary.
(Refer to 23 - BODY/SUNROOF/GLASS PANEL -
ADJUSTMENTS)
8. Install headliner. (Refer to 23 - BODY/INTERIOR/
HEADLINER - INSTALLATION)
23 - 264
SUNROOF
KJ
SEAL-SUNROOF GLASS
REMOVAL
1. Remove sunroof glass panel. (Refer to 23 - BODY/SUNROOF/GLASS PANEL - REMOVAL)
2. Place glass panel on clean work area with the top side up. Support the glass assembly from underside to avoid
bending or otherwise damaging the mounting tabs.
3. Grasp the seal and pull seal away from the glass panel. The seal is a one piece seal.
INSTALLATION
NOTE: Always position seal seam on center of the passenger side of glass panel.
1. Place seal into position.
2. Install seal on glass. Using care working the seal around the glass, being careful not to over stretch the seal
while installing.
3. Install the glass panel. (Refer to 23 - BODY/SUNROOF/GLASS PANEL - INSTALLATION)
KJ
SUNROOF
23 - 265
SUNSHADE
REMOVAL
1. Remove glass assembly from the sunroof assem-
bly.
(Refer
to
23
-
BODY/SUNROOF/GLASS
PANEL - REMOVAL)
2. Remove two screws (3) from trough assembly (1).
3. Remove trough assembly (1).
4. Slide the sunshade forward to disengage the guide
feet from the tracks through the cutouts at the front
of the tracks.
CAUTION: Use care not to crease the sunshade
when removing or installing.
INSTALLATION
1. Place sunshade into position, through the cutouts
at the front of the tracks and slide the sunshade
back.
2. Place trough (1) assembly into position on sunroof
module and install the screws (3).
3. Install the glass panel. (Refer to 23 - BODY/SUN-
ROOF/GLASS PANEL - INSTALLATION)
23 - 266
SUNROOF
KJ
TRIM LACE
REMOVAL
1. Remove lace by starting at the joint center of the
opening on driver’s side.
2. Pull one end of the lace away from the headliner
until the entire lace is removed.
INSTALLATION
1. Place end of trim lace into position starting at cen-
ter of the opening on driver’s side.
2. Push lace into position.
3. Ensure that the corner radii is fully engage.
4. Once trim lace is attached to sunroof module begin
tucking the headline under the lip on the trim lace
working all the way around the opening.
KJ
SUNROOF
23 - 267
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст