Engines Iveco C10,C13, Cursor 10, Cursor 13. Manual — part 46
Figure 5
Figure 6
Figure 7
Figure 8
-
Remove the engine supports;
-
remove the drive (1).
104247
104248
-
Secure the engine to the rotary stand with the brackets (1).
-
Drain the lubricating oil from the sump.
Only for types: F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
-
Using a suitable tool (3), work in the direction of the arrow
on the tightener (2) and remove the belt (1).
104249
Remove:
-
alternator (2).
-
supports (1 and 3).
104249/A
8
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
Figure 9
Figure 10
Figure 11
Figure 12
104251
Remove:
-
thermostat assembly (8);
-
pipes complete with coolant (6);
-
pulley (4);
-
water pump (7);
-
automatic tightener support (1);
-
fixed tightener (5);
-
damper flywheel (3) and pulley beneath;
-
automatic tightener (2);
With the extractor 99340053 (2) applied as shown in the
figure, extract the seal (4). Undo the screws (3) and take off
the cover (1). Disconnect all the electrical connections and
sensors.
99361
For all types except F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
On the engine exhaust side, remove the following parts:
-
oil delivery pipe (1);
-
oil return pipe (4);
-
turbocharger (3);
-
exhaust manifold (2).
104252
1
2
4
3
Using tool 99360314 unscrew the oil filters (3).
Remove fastening screws (1) and disassemble heat exchanger
(2).
101605
Figure 13
Disconnect the fuel pipes (1) from the fuel pump (2).
Remove:
-
the fuel pump (2);
-
fuel filter (3) and fuel pipes (1).
104254
SECTION 3 - INDUSTRIAL APPLICATION
9
F3B CURSOR ENGINES
Loosen the screws (1) and remove the intake manifold (2)
from the engine.
Figure 14
Figure 15
Figure 16
104783
Figure 17
Remove:
-
the starter motor (1);
-
the control unit (2) and its support;
-
the oil dipstick (3) from the crankcase.
104310
Figure 18
85480
Remove the rocker arm cover (1), take off the screws (2) and
remove: the cover (3), the filter (5) and the gaskets (4 and 6).
Take off the screws (8) and remove the blow-by case (7).
60496
-
Unscrew the screws (2) and remove the gear (1) fitted
with phonic wheel.
60497
-
Unscrew the screws (1); tighten one screw in a reaction
hole and remove the shoulder plate (2), remove the sheet
gasket.
The air intake joint (3) may have different positions
depending on the type of engine.
NOTE
10
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
60498
60500
60499
60501
104257
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Unscrew the screws (2) and remove the transmission gear (1).
Stop the engine flywheel (3) rotation by means of tool
99360351 (1), unscrew the fixing screws (2) and remove the
engine flywheel (3).
Apply the extractor 99340054 (2) and pull out the seal
gasket (1).
Unscrew the screws (1) and take down the gearbox (2).
- Disconnect the electrical connections from the pump
injectors.
- Unscrew the screws (1) fixing the rocker arm shaft.
In sequence, take out the:
- idle gear (1);
- oil pump gear (2).
99364
Figure 24
SECTION 3 - INDUSTRIAL APPLICATION
11
F3B CURSOR ENGINES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст