Engines Iveco C10,C13, Cursor 10, Cursor 13. Manual — part 47
Figure 25
116814
60514
102935
60515
104784
Figure 26
Figure 27
Figure 28
Figure 29
Apply tool 99360553 (1) to the rocker holder shaft (5) and
remove the shaft (5) from the cylinder head.
To extract the pump injector from the engine block, using the
tool proceed as follows:
- Hook up the detail (3) of the tool illustrated in the figure
to the injector pump (4);
- fit part (2) on part (3), resting the former on the cylinder
head;
- tighten the nut (1) and extract the pump injector (4) from
the engine block
- Fit the plugs 99360180 (1) instead of injectors.
- Remove the camshaft (2).
- Unscrew the fixing screws on the cylinder head (3).
- By means of metal ropes, lift the cylinder head (1).
- Remove the seal (2)
Only for types: F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
Loosen screws (3), then remove sump (1) complete with
spacer (2) and seal gasket (4).
Figure 30
101606
Loosen screws (3), then remove sump (1) complete with
spacer (2) and seal gasket (4).
For all types except: F3BE0684J*E902 - F3BE9687A*E001
- F3BE9687B*E001 - F3BE9687C*E001
12
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
101607
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
Loosen the screws, then remove suction strainer (1).
Using the centring ring 99396035 (2), check the exact position
of the cover (1). If it is wrong, proceed accordingly and lock
the screws (3).
Key on the gasket (1), mount the key 99346250 (2) and,
screwing down the nut (3), drive in the gasket (1).
Check that the pistons 1-6 are exactly at the T.D.C.
Put the gasket (2) on the crankcase.
Mount the cylinder head (1) and tighten the screws as shown
in Figs. 34-35-36.
Diagram of the tightening sequence of the screws fixing the
cylinder head.
- Pre-tightening with the torque wrench (1):
1
st
phase: 60 Nm (6 kgm).
2
nd
phase: 120 Nm (12 kgm).
60563
60564
60515
60565
61270
Lubricate the thread of the screws with engine oil
before assembly.
ENGINE ASSEMBLY
NOTE
Use new screws every time the under block is
re-assembled.
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
13
F3B CURSOR ENGINES
Apply LOCTITE 5970 IVECO n˚ 2992644 silicone on the gear
housing, using appropriate tools (1), as shown in the figure.
The sealer string (1) diameter is to be 1,5
±
Using a torque wrench, tighten the highlighted screws with the
following sequence and tightening torques:
4 screws M12 x 1.75 x 35
63 Nm
10 screws M12 x 1.75 x 100
63 Nm
1 screw M12 x 1.75 x 120
63 Nm
2 screws M12 x 1.75 x 70
63 Nm
Figure 37
Figure 38
Figure 39
60566
- Closing to angle with tool 99395216 (1):
3
rd
phase: angle of 120
°.
4
th
phase: angle of 60
°.
Mount the oil pump (4), the intermediate gears (2) together
with the link rod (1) and lock the screws (3) in two phases:
pre-tightening
30 Nm.
closing to angle
90
°.
104311
60567
104281
Figure 40
Figure 41
α
Key on the gasket (1), mount the keying device 99346251 (2)
and, screwing down the nut (3), drive in the gasket.
Mount the gear housing within 10 min. of applying
the sealant.
α
104282
2 screws M12 x 1.75 x 193
63 Nm
:
0.5
0.2
NOTE
14
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
Apply LOCTITE 5970 IVECO n˚ 2992644 silicone on the gear
housing, using appropriate tools (1), as shown in the figure.
The sealer string (1) diameter is to be 1,5
±
Using a torque wrench, tighten the highlighted screws with the
following sequence and tightening torques:
4 screws M12 x 1.75 x 35
63 Nm
10 screws M12 x 1.75 x 100
63 Nm
1 screw M12 x 1.75 x 120
63 Nm
2 screws M12 x 1.75 x 70
63 Nm
Figure 42
104785
104786
Figure 43
Figure 44
Key on the gasket (1), mount the keying device 99346251 (2)
and, screwing down the nut (3), drive in the gasket.
Mount the gear housing within 10 min. of applying
the sealant.
104787
2 screws M12 x 1.75 x 193
63 Nm
:
0.5
0.2
Only for types: F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
15
F3B CURSOR ENGINES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст