Engines Iveco C87 / Cursor 87. Manual — part 9
2
SECTION 3 - INDUSTRIAL APPLICATION
F2C CURSOR ENGINES
Base - June 2006
- High pressure pump (pressure regulator)
38
. . . .
- Flywheel pulse transmitter
39
. . . . . . . . . . . . . . .
- Distribution pulse transmitter
40
. . . . . . . . . . . . .
- Fuel pressure sensor on rail
43
. . . . . . . . . . . . . .
- Alternator
44
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Starting motor
45
. . . . . . . . . . . . . . . . . . . . . . . .
EDC SYSTEM FUNCTIONS
46
. . . . . . . . . . . . . . . .
PART THREE - TROUBLESHOOTING
49
. . . . . . .
METHODS OF DIAGNOSIS
51
. . . . . . . . . . . . . . . .
PT-01 PORTABLE TESTER
52
. . . . . . . . . . . . . . . . .
- Main functions
52
. . . . . . . . . . . . . . . . . . . . . . . .
- Test parameters
52
. . . . . . . . . . . . . . . . . . . . . . .
PREFACE
53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAULT CODES
54
. . . . . . . . . . . . . . . . . . . . . . . . . .
PART FOUR -
MAINTENANCE PLANNING
57
. . . . . . . . . . . .
MAINTENANCE
59
. . . . . . . . . . . . . . . . . . . . . . . . .
- Maintenance services chart
59
. . . . . . . . . . . . . . .
CHECKS AND/OR MAINTENANCE WORK
60
. . .
OFF-PLANE OPERATIONS
61
. . . . . . . . . . . . . . . . .
Data, features and performances are valid only if the setter fully complies with all the installation prescriptions provided
by FPT.
Furthermore, the users assembled by the setter shall always be in conformance to couple, power and number of turns
based on which the engine has been designed.
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
3
F2C CURSOR ENGINES
CLEARANCE DATA
TECHNICAL CODE
Type
F2CE9687
Type
A*E
B*E
Cycle
4-stroke Diesel engine
4-stroke Diesel engine
Fuel feed
Turbocharged
Turbocharged
Injection
Direct
No. of cylinders
6 in line
∅
Bore
mm
117
Stroke
mm
135
+
+
+
Total displacement
cm
3
8710
ρ
Compression ratio
1: 15.9
± 0.8
Maximum
kW
power
(HP)
rpm
260
314
2100
230
305
2100
Max. torque
Nm
(kgm)
rpm
1500
1400
1400
1400
Loadless
engine
idling
rpm
-
Loadless engine
peak
rpm
-
SUPERCHARGING
Intercooler
Direct injection
Turbocharger type
j
HX40
bar
LUBRICATION
Oil pressure
(warm engine)
- idling
bar
- peak rpm
bar
Forced by gear pump, relief valve single action
oil filter
-
-
COOLING
Water pump control
Thermostat
- start of opening
ºC
Liquid
Through belt
85
114008
114007
Figure 1
Figure 2
Figure 3
540110
ENGINE
DISASSEMBLY
ON
BENCH
If air conditioner compressor is installed, cut belt (2) as it must
not be reused.
Use specific tool (1) and operate in the arrow direction to
remove water pump and alternator control belt (5).
Remove screws and separate pulleys (3) and (6) with damping
flywheel (4).
Remove parts below:
- alternator (1);
- belt tensioner (2);
- if present, air conditioner compressor (3);
- water pump (6);
- flanged pipe (4);
- fixed belt tensioner (5);
- thermostat assembly (7).
Before installing engine on rotary stand 99322230,
remove parts that might interfere with the
installation of brackets 99361042.
Therefore, remove heat exchanger and oil line as
shown below.
NOTE
114016
Unlock retaining screws (2) and remove head cover (1) to
reach injector and rail wiring.
Remove wiring from all components shown in “Electric
equipment“ section.
114017
Under heat exchanger (2) place a container for engine coolant
drain.
Unlock retaining screws and remove heat exchanger assembly
(2).
Remove oil outlet line (1).
Install engine on rotary stand 99322230.
Drain sump oil in specific container.
Figure 4
SECTION 3 - INDUSTRIAL APPLICATION
7
F2C CURSOR ENGINES
114012
114015
114013
Figure 5
Figure 6
Figure 7
Figure 8
Remove parts below:
- fuel filter (3);
- oil level rod (2);
- intake manifold (1).
Disconnect line (1) from high pressure pump support and
remove ECU (2) with support below.
Remove screws (1) and blow-by box (2).
114010
Remove parts below:
- oil filter (1);
- oil inlet line (2);
- turbocompressor (4) and exhaust manifold (3).
On opposite engine side, remove start-up motor.
114551
Apply extractor 99340051 (2) and remove seal (1).
Unlock screws and remove front cover (3).
Figure 9
8
SECTION 3 - INDUSTRIAL APPLICATION
F2C CURSOR ENGINES
Base - June 2006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст