Geely FC. Manual part — 32
Geely FC. Manual part - 32
Drive shaft--Left front shaft hub assembly
11. Disassemble left front shaft hub assembly.
(a) Use special tool to disassemble shaft hub.
(b) Use special tool to disassemble inner ring (exterior) seat
from shaft hub.
12. Disassemble left front brake bottom board.
Disassemble three bolts, then take down the brake bottom
board.
13. Disassemble left front shaft hub bearing
(a) Put inner circle (exterior) on bearing.
(b) Use special tool and press to disassemble the bearing from
steering knuckle.
14. Assemble left front shaft hub bearing.
Use special tool and press to assemble the bearing on steer-
ing knuckle.
15. Assemble left front brake bottom board.
Assemble bottom board with three bolts.
16. Assemble left front shaft hub assembly.
Use special tool and press to assemble shaft hub.
17. Assemble the clasp of left front shaft hub hole.
Use the clasp pliers to assemble the clasp.
Special
tool
Special tool
Special
tool
Special
tool
125
Special tool
Special
tool
Special
tool
18. Assemble left front lower control arm ball head as-
sembly [64000093]
(a) Assemble lower ball head and locking nut.
Torque: 103
±±±±± 10 N⋅⋅⋅⋅⋅m
(b) Assemble new cotter pin.
If hole position of cotter pin could not make a line, lock the
screw cap for 60
again.
19. Assemble left front shaft hub assembly
(a) Assemble two bolts and nuts, and assemble shaft hub as-
sembly on absorber.
Torque: 153
±±±±± 10 N⋅⋅⋅⋅⋅m
Note: when the bolts and nuts should be used again,
spread engine oil on the thread of nuts.
(b) Push the front shaft hub assembly to the outside of
automobile, then assemble transmission shaft assembly
in the gear slot of front shaft hub assembly.
Note:
Front shaft assembly could not be pushed to outside
too much.
z
Do not damage the exterior joint dustproof cover of
drive shaft.
z
Do not damage the stator of speed sensor.
20. Assemble left lower control arm assembly
[64000091]
Assemble lower control arm and ball head with two nuts and
bolts.
Torque: 142
±±±±± 10 N⋅⋅⋅⋅⋅m
21. Assemble left transversal lever assembly
(a) Connect transversal lever to steering knuckle.
(b) Assemble screw cap and new cotter pin.
Torque: 49
±±±±± 5 N⋅⋅⋅⋅⋅m
22. Assemble left front brake assembly [64000134]
23. Assemble front brake caliper assembly
(a) Assemble brake caliper assemble on steering knuckle with
two bolts.
Torque: 106
±±±±± 10 N⋅⋅⋅⋅⋅m
24. Assemble fixing nuts of left front drive shaft
[64000083]
Use torque wrench (30mm) to assemble new fixing nuts.
25. Disassemble left front brake branch pump assembly
26. Disassemble left front brake assembly [64000134]
27. Check the axial clearance of bearing
Drive shaft--Left front shaft hub assembly
126
Drive shaft--Left front shaft hub assembly
Use centimeter to check the axial clearance of shaft hub center.
Maximal value: 0.05 mm
If axial clearance exceeds the maximal value, it is necessary
to change the bearing.
28. Check the terminal face run-out of shaft hub.
Use centimeter to check the terminal run-out of exterior sur-
face of shaft hub.
Maximal value: 0.05 mm
If terminal run-out exceeds the maximal value, change the shaft
hub.
29. Assemble left front brake assembly [64000134]
30. Assemble left front brake branch pump assembly
Use two bolts to assemble brake branch pump assembly on
steering knuckle.
Torque: 106
±±±±± 10 N⋅⋅⋅⋅⋅m
31. Assemble speed sensor assembly of left front wheel
[67000020]
(a) Assemble wiring harness of speed sensor and brake hose
on the absorber with bolts.
Torque: 29 N
⋅⋅⋅⋅⋅m
(b) Use the bolts to assemble speed sensor to steering knuckle.
Torque: 8.0 N
⋅⋅⋅⋅⋅m
Note: Do not damage the speed sensor.
z
Prevent it from contacting with sundries.
z
When assembling the sensor, wiring harness of sen-
sor could not bend.
32. Assemble fixing nut of left front drive shaft
[64000083]
(a) Assemble new fixing nuts,
Torque: 216
±±±±± 15 N⋅⋅⋅⋅⋅m
(b) Use chisel and hammer to make fixing nut concave and fix
them.
33. Assemble front wheels.
Torque: 103
±±±±± 10 N⋅⋅⋅⋅⋅m
34. Check and adjust wheel alignment (referring to page
87).
35. Check the ABS speed sensor signal.
127
Drive shaft--Left front shaft hub bolt
Left front shaft hub bolt
Change
Hint: changing procedure for right side is same as left
side.
1. Disassemble front wheels
2. Disassemble left front brake branch pump assembly
3. Disassemble left front brake assembly [64000134]
4. Disassemble left front brake bottom board.
Disassemble three bolts, then disassemble the bottom board
from steering knuckle.
5. Disassemble left front shaft hub bolt.
Use special tool and screw driver to disassemble shaft hub
bolt.
6. Assemble left front shaft hub bolt.
(a) Liking that shown in figure, assemble gasket and screw
cap on new shaft hub bolt.
(b) Use screw driver to fix and lock the screw cap to make the
bolt enter the hole.
7. Assemble left front brake bottom board.
Assemble three bolts, and assemble bottom board in steering
knuckle.
8. Assemble left front brake assembly.
9. Assemble left front brake branch pump assembly.
Torque: 106
±±±±± 10 N⋅⋅⋅⋅⋅m
10. Assemble front wheels.
Torque: 103
±±±±± 10 N⋅⋅⋅⋅⋅m
128
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст