Geely FC. Manual part — 31
Geely FC. Manual part - 31
Driveshaft--Front drive shaft
Transmission shaft
Left mm
Right mm
A type
570.2 ± 5
842.7 ± 5
B type
570.2 ± 5
847.3 ± 5
C type
570.2 ± 5
844.7 ± 5
(b) Mesh clamp type:
Liking that shown in figure, use pliers to assemble No.2
fixing clamp of inner joint dust-proof cover.
32. Check front drive shaft.
(a) Check whether there is any obvious clearance on exterior
joint.
(b) Check whether inner joint could slide smoothly in pushing
direction.
(c) Check whether there is any obvious clearance of inner joint
in radial direction.
(d) Check whether the dustproof cover is damaged.
Note: drive shaft assembly should keep moving on hori-
zontal position.
33. Assemble left front drive shaft assembly [64000082]
(a) Spread ATF on gear slot of inner joint shaft assembly.
(b) Put gear slot of drive shaft in integrated transmission, then
use copper stick and hammer to knock drive shaft to its
position.
Note:
z
make the placket of clasp face the downside to
assemble.
z
Be careful not to damage the seal oil
Hint: Whether the drive shaft contacts with gear shaft
could be felt by the sound or feeling in running process.
(c) Assemble seal board of left front swing board.
34. Assemble left front shaft hub assembly.
Assemble left front drive shaft assembly to left front hub assembly.
Note:
z
Do not damage exterior joint dustproof cover.
z
Do not damage the stator of speed sensor.
Hint: A size, please referring to following table.
Pliers
clamp
121
Drive shaft--Front drive shaft
35. Assemble left lower control arm assembly [64000091]
(a) Assemble lower ball joint on lower suspension arm with the
bolts and screw caps.
Torque: 142 ± 10 N
⋅⋅⋅⋅⋅m
36. Assemble left transversal lever assembly.
(a) Assemble transversal lever terminal to steering knuckle with
screw cap.
Torque: 49 ± 5 N
⋅⋅⋅⋅⋅m
(b) Assemble new cotter pin.
Note: if hole position of cotter pin could not make a
line, lock the screw cap for 60.
37. Assemble speed sensor assembly of left front
wheels (equipping with ABS) [67000020]
(a) Assemble speed sensor absorber with bolts.
Torque: 49 ± 5 N
⋅⋅⋅⋅⋅m
(b) Assemble speed sensor on the steering knuckle with bolts.
Torque: 8 N
⋅⋅⋅⋅⋅m
Note:
z
Do not damage speed sensor.
z
Prevent it from contacting with sundries.
z
When assembling the sensor, the wiring harness
of sensor could not bend.
38. Assemble fixing nuts of drive shaft [68000083]
(a) Assemble fixing nuts.
Torque: 216 ± 15 N
⋅⋅⋅⋅⋅m
(b) Use chisel and hammer to knock the fixing nuts concave
and fix them.
39. Assemble front wheels.
Torque: 103 ± 10 N
⋅⋅⋅⋅⋅m
40. Add the oil in gearbox.
41. Check and adjust the oil in gearbox.
42. Check and adjust wheel alignment (referring to page
87)
43. Check the ABS speed sensor (equipping with ABS).
44. Test on road.
122
Driveshaft--Left front shaft hub assembly
Left front shaft hub assembly
Change
Hint: changing procedure for right side is same as the left
side.
1. Disassemble front wheels
2. Disassemble fixing nuts of left front drive shaft
[64000083]
(a) Use special tool and hammer to unclench concave part of
fixing nuts.
(b) Disassemble fixing nuts.
3. Disassemble speed sensor assembly of left front
wheel [67000020]
(a) Disassemble the bolts, then disassemble the wiring har-
ness of sensor and brake hose.
(b) Disassemble the bolts, then disassemble speed sensor
from steering knuckle.
4. Disassemble left front brake caliper assembly
Disassemble two bolts to disassemble brake caliper bracket.
Special
tool
123
Drive shaft--Left front shaft hub assembly
5. Disassemble left front brake assembly [64000134]
6. Disassemble left transversal lever assembly
(a) Disassemble cotter pin and nuts.
(b) Use special tool to disassemble transversal lever assembly
from steering knuckle.
7. Disassemble left lower control arm assembly
[64000091]
Disassemble the bolt and two nuts, then disassemble lower
control arm from lower ball joint.
8. Disassemble left front shaft hub assembly.
(a) Use plastic hammer to disassemble transmission shaft from
shaft hub.
Note: do not damage the dustproof cover and the sta-
tor of ABS speed sensor.
(b) Disassemble two bolts and nuts, then disassemble steer-
ing knuckle with shaft hub.
9. Disassemble left front lower control arm ball head
assembly [64000093]
(a) Disassemble cotter pin and nut.
(b) Use special tool to disassemble ball head.
10. Disassemble the clasp in left front shaft hub hole.
Use clasp pliers to disassemble the clasp.
124
Special
tool
Special tool
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст