Geely FC. Manual part — 30
Geely FC. Manual part - 30
Drive shaft--Front drive shaft
Left and right driving shaft
Capacity of lubricating grease
B type
125-135 grams
C type
190-200 grams
19. Disassemble clasp of inner joint of left front drive
shaft.
Use screw driver to disassemble the clasp.
20. Disassemble dustproof cover of left front drive
shaft.
Use special tool and press to disassemble dustproof cover .
21. Assemble dustproof cover of left front driveshaft.
Liking that shown in figure, use special tool and press to as-
semble left dustproof cover
Note: Dustproof cover should be assembled to its position
completely.
Do not damage dustproof cover lid.
22. Assemble the clasp of inner joint of left front drive
shaft.
Assemble new clasp.
23. Assemble exterior joint dustproof cover (B type and
C type).
(a) Twist ethylene adhesive tape on gear slot of exterior joint to
prevent damage.
(b) Assemble following parts on drive shaft by sequence.
(1) No.2 fixing clamp of exterior joint dustproof cover.
(2) Exterior joint dustproof cover
(3) Fixing clamp of exterior joint dustproof cover.
(c) Fill lubricating grease in exterior joint assembly.
(d) Assemble exterior joint dustproof cover on exterior joint shaft.
24. Assemble No.2 fixing clamp of exterior joint
dustproof cover of left front drive shaft.
(a) AUMIGA fixing type.
Tighten big fixing clamp of exterior joint.
Special tool
Special tool
117
(1) Put big fixing clamp on dustproof cover firmly.
(2) Put special tool on big fixing clamp.
(3) Lock special tool to tighten big fixing clamp.
Note: do not tighten special tool too much.
(4) Use special tool to adjust the clearance of big fixing
clamp.
Clearance:
≤≤≤≤≤ 0.8mm
25. Assemble fixing clamp of exterior joint dustproof
cover of left front drive shaft.
(a) AUMIGA fixing type.
Tighten small fixing clamp of exterior joint.
(1) Put small fixing clamp on dustproof cover firmly.
(2) Put special tool on small fixing clamp.
(6) Lock special tool to tighten small fixing clamp.
Note: do not tighten special tool too much.
(4) Use special tool to adjust the clearance of small fixing
clamp.
Clearance:
≤≤≤≤≤ 0.8mm
26. Assemble dynamic absorber of driveshaft (right
drive shaft).
(a) A type and C type
Liking that shown above, set up the distance of absorber:
Drive shaft--Front drive shaft
A type and C type
440
± 2mm
118
Special
tool
Special
tool
Special
tool
Drive shaft--Front drive shaft
(b) B type
Liking that shown above, set up the distance of absorber:
27. Assemble fixing clamp of dynamic absorber of drive
shaft.
(a) Single-contact fixing clamp type:
Assemble new fixing absorber clamp on the absorber of drive
shaft, then fix the fixing clamp with screw driver.
(b) Mesh clasp type:
Assemble new fixing absorber clamp on the absorber of drive
shaft, then fix the fixing clamp with screw driver.
28. Assemble inner joint of left front drive shaft.
(a) Twist ethylene adhesive tape on gear slot of exterior joint to
prevent damage.
(b) Assemble following parts on drive shaft by sequence.
(1) No.2 fixing clamp of inner joint dustproof cover.
(2) Inner joint dustproof cover
(3) Fixing clamp of inner joint dustproof cover.
(c) Align the mark made before disassembly, and assemble
triangle joint in drive shaft.
(d) Assemble triangle joint assembly with copper stick and
hammer.
Note: do not knock the stator.
Single-contact fixing
clamp type
Mesh clamp type
Align the
mark
119
B type and C typ
470 ± 2mm
Drive shaft--Front drive shaft
(e) Use clasp spreading pliers to assemble the clasp.
(f) Fill lubricating grease in inner joint assembly.
(g) Align the mark before disassembly, and assemble inner joint
in drive shaft.
29. Assemble dustproof cover inner joint of left front
drive shaft.
Assemble inner joint dustproof cover to inner joint and drive
shaft.
30. Assemble fixing clamp of dustproof cover inner joint
of left front drive shaft.
(a) Single-contact fixing clamp type:
Liking that shown in figure, use screw driver to assemble
fixing clamp of dust-proof cover inner joint .
(b) Mesh clamp type:
Liking that shown in figure, use pliers to assemble fixing
clamp of inner joint dust-proof cover.
31. Assemble No.2 fixing clamp of dust-proof cover in-
ner joint of left front drive shaft.
(a) Single-contact fixing clamp type:
Liking that shown in figure, use screw driver to assemble
No.2 fixing clamp of dust-proof cover inner joint.
A type
A type
180-190 grams
C type
C type
B type
B type
125-135 grams
Pliers
clamp
120
Left transmis-
sion shaft
Right trans-
mission shaft
Capacity of lubricating grease
Align the mark
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст