Geely FC. Manual part — 29
Geely FC. Manual part - 29
Drive shaft--Front drive shaft
Front drive shaft
Overhaul
Hint: overhaul procedure for right side is same as the left
side.
1. Check the drive shaft (referring to page 111).
2. Discharge the oil in gearbox.
(a) Disassemble oil plug and gasket to discharge the oil in
gearbox.
(b) Change with a new gasket and assemble oil discharging
plug.
Torque: 45
±±±±± 5 N·m
3. Disassemble front wheels.
4. Disassemble fixing nut of drive shaft [64000083]
(a) Use special tool and hammer to unclench the concave part
of fixing nut.
(b) Disassemble the fixing nut.
5. Disassemble speed sensor assembly of left front
wheels (equipping with ABS) [67000020]
(a) Disassemble the bolt, and disassemble sensor wiring har-
ness and brake hose from the absorber.
(b) Disassemble the bolt, and disassemble speed sensor from
steering knuckle.
special
tool
113
6. Disassemble left transversal lever assembly.
(a) Disassemble cotter pin and screw cap.
(b) Use special tool to disassemble terminal assembly from
steering knuckle.
7. Disassemble left lower control arm assembly
[64000091]
Disassemble the bolt and two nuts, then disassemble lower
control arm from lower ball joint.
8. Disassemble wheel hub assembly of left front wheel.
Use plastic hammer to disassemble drive shaft from wheel hub.
Note: forbid damaging dust-proof cover and the rotator of
speed sensor.
9. Disassemble left front drive shaft assembly
[64000082]
(a) Disassemble the seal board of left front fender.
(b) Use special tool to disassemble front drive shaft assembly.
Note: do not damage oil seal.
10. Fix left front shaft hub assembly.
Note: if supporting automobile weight only with bearing,
shaft hub bearing will be damaged; for example, when
moving automobile in process of disassembling drive
shaft. So, if it is not necessary to support automobile
weight with shaft hub bearing, it is necessary to use
special tool to support.
11. Disassemble No.2 fixing clamp of inner joint dust-
proof cover of left front drive shaft.
(a) Single-contact fixing clamp type:
Use screw driver to disassemble No.2 fixing clamp of inner
joint dust-proof cover of left front drive shaft.
Drive shaft--Front drive shaft
special tool
special tool
114
Drive shaft--Front drive shaft
(b) Mesh clamp type:
Liking that shown in figure, use pliers to disassemble No.2
fixing clamp of inner joint dust-proof cover of left front trans-
mission shaft.
12. Disassemble fixing clamp of inner joint dustproof
cover of left front drive shaft.
(a) Single-contact fixing clamp type:
Use screw driver to disassemble fixing clamp of inner joint
dust-proof cover.
(b) Mesh clamp type:
Liking that shown in figure, use pliers to disassemble No.2
fixing clamp of inner joint dust-proof cover.
13. Disassemble inner joint dustproof cover of left front
drive shaft.
Disassemble dustproof cover from left inner joint.
14. Disassemble inner joint of left front drive shaft.
(a) Remove old lubricating grease of inner joint.
(b) Make mark on inner joint and drive shaft.
Note: do not use punch to make mark.
(c) Disassemble inner joint assembly from drive shaft.
(d) Use clasp spreading pliers to disassemble the clasp.
Pliers
clamp
Align the mark
Pliers clamp
115
(e) Make mark on transmission shaft and triangle joint.
Note: do not use the punch to make mark.
(f) Use copper stick and hammer to disassemble triangle joint.
Note: do not knock the stator position.
(g) Disassemble No.2 fixing clamp of inner joint dustproof cover
and fixing clamp of inner joint dustproof cover.
15. Disassemble the absorber of drive shaft (right trans-
mission shaft).
(a) Single-contact fixing clamp type:
Liking that shown in figure, use screw driver to disassemble
fixing clamp.
(b) Mesh clamp type.
Liking that shown in figure, use pliers to disassemble fixing
clamp.
(c) Disassemble dynamic absorber of drive shaft.
16. Disassemble No.2 fixing clamp of exterior joint
dustproof cover of left front drive shaft.
(a) Use screw driver to disassemble No.2 fixing clamp of exte-
rior joint dustproof cover.
17. Disassemble fixing clamp of exterior joint dustproof
cover of left front drive shaft.
(a) Use screw driver to disassemble fixing clamp of exterior
joint dustproof cover.
18. Disassemble fixing clamp of exterior joint dustproof
cover (B type and C type).
(a) Disassemble dustproof cover of exterior joint.
(b) Remove old lubricating grease of exterior joint.
Drive shaft--Front drive shaft
Align the mark
Copper stick
Single-contact fixing
clamp type
Mesh clamp type
116
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст