Geely CK (2008). Manual part — 7
Geely CK (2008). Manual part - 7
25
(b) Remove the counter gear of the camshaft.
(1) Clamp the camshaft's hexagon on the vise.
(2) Turn the counter gear cloclwise, Remove the service bolt.
(3) Remove the snap ring with a circlip pliers. See (Figure 57).
(4) Remove waved gasket, camshaft counter gear and the camshaft gear spring. See (Figure 58)
24. Remove and install spark plug hole gasket. See Provision 15 and 16, Section 3 Timing Belt
Replacement for detailed information. See (Figure 44, 45).
Figure 57
25. Install camshaft
(a) Install exhaust camshaft and turn camshaft counterclockwise to make the dowel pin cross the vertical
line a little. See (Figure 59).
(b) Apply grease to a new oil seal lip and install it into the oil seal. See (Figure 60).
Figure 59
(c) Install camshaft counter gear.
(1) Clamp the camshaft's hexagon head with a vise.
(2) Install camshaft gear spring, camshaft counter gear and waved washer. (Figure 61).
Hint: Align the pin on the gear to the spring end of the counter gear.
(3) Install the snap ring with a circlip plier.
(4) Turn the counter gear clockwise with the special tool. Align the
holes on the camshaft drive gear. Install the service bolt.
Figrue 61
Rotate
Figure 58
Figure 60
26
(d) Install intake camshaft.
(1) Make the exhaust camshaft dowel pin a bit higher than the top of the cylinder head.
(2) Apply grease to camshaft's contact surface.
(3) Install intake camshaft gear to exhaust camshaft gear ,
Align the matchmarks on each gear. See (Figure 62).
(4) Check the timing marks on the camshaft gear for
alignment.See (Figure 63).
Hint: Matchmark is on the top.
26. Adjust valve clearance
27. Install camshaft timing pulley
Turn the camshaft's hexagon head. Tighten the timing pulley bolt. See (Figure 64).
Torque: 59N. M
Figure 63
Figure 65
28. Install the timing belt
(a) Align the marks on timing belt and the one on camshaft timing pulley.
(b) Install timing belt. Check tension force between the crankshaft timing pulleys. See (Figure 65).
29. Check valve timing
(a) Loose idler bolt.
(b) Turn crankshaft from TDC clockwise for 2 cycles.
(c) Check and align each pully to the timing mark as shown in Figure 66. Remove timing belt and reinstall it
if not.
30. Install crankshaft gear or pulley cover sub-assembly
Torque: 9.3N. m
Figure 62
Install Mark
Timing Mark
Install Mark
Install Mark
Timing Mark
5-6mm
Figure 64
Figure 66
27
31. Install timing belt cover
Torque: 9.3N. m
32. Install generator assembly
33. Install right engine mounting bracket. See (Figure 67)
34. Install cylinder head cover sub-assembly
(a) Install 2 ventilation PCV hoses to the cylinder head cover.
(b) Connect the generator wire.
(c) Install the wire clip.
(d) Connect A/C compressor switch connector.
35. Install water pump pulley
36. Install power steering pump V-belt
37. Install A/C compressor to crankshaft pulleyV-belt
38. Install generator V-belt
39. Install left & right rear mounting bracket of engine.
40. Install ignition coil and high voltage cable
41. Hoist the engine back into the compartment
42. Install propeller shaft
43. Install air filter assembly with hose
44. Install oil pipe and water hoses
45. Install left and right front tires.
46. Check engine oil for leakage
47. Install all the wire harnesses and the cables on the engine connected to car body
Figure 67
28
Section 5 Cylinder Head Gasket Replacement
Component 1
Figure 68
Vane Pump Assembly V/ Power Steering
Throttle Body Assembly
Gasket
Dipstick
Inlet Pipe
Gasket
Wire Harness
O-Ring
Timing Chain Or Timing Belt Cover No. 2
Crankshaft Or Pulley Cover Sub-Assembly
Fan Pulley
Fuel Delivery Pipe No.1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст