Geely Emgrand X7. Manual part — 647
Geely Emgrand X7. Manual part - 647
11.14.7.3 Unsecure warning lamp for passenger side safety belt is always "ON"
Circuit diagram:
NL11-4030b
7 IP15
2 SO07
1 SO07
W/
R
乘客
安全带
开关
PASBLT
SRS
4 IP03
多功能仪表
1
2
SO03
SO03
坐人
传感器
Diagnostic steps:
1
Inspect the manned sensor.
(a) Disconnect manned sensor harness connector.
(b) Use multimeter to measure the connection situation of switch.
Test Terminal
Conditions
Specified Value
S013(1)--S013(2) Passenger
Side Not Occupied
Less than 1 Ω
S013(1)--S013(2) Passenger Side Occupied
10 kΩ or higher
Confirm whether the resistance is at a specified value.
2
Replace the manned sensor.
(a) Refer to 9.2.7.10 Replacement of passenger detection sensor.
Confirm whether the alarm lamp displays normally if the multifunctional instrument
passenger-side safety belt is not worn.
Yes
Go to step 3
No
Passenger
sensor
Passenger
safety belt
switch
Multifunction
instrument
2587
3
Inspect the passenger-side safety belt switch.
(a) Disconnect wire harness connector SO07 of passenger's side safety belt.
(b) Use multimeter to measure resistance between passenger's side safety belt wire harness
connector SO07 terminal No. 1 and No.2.
Test Terminal
Conditions
Specified Value
S007(1)--S007(2) Insert
safety belt
Less than 1 Ω
S007(1)--S007(2) Remove
the safety belt.
10 kΩ or higher
4
Replace passenger-side safety belt buckle assembly.
(a) Replace passenger side safety belt buckle assembly.
Confirm whether the alarm lamp displays normally if the multifunctional instrument
passenger-side safety belt is not worn.
5 Inspect
the
circuit.
(a) Closed ignition switch to OFF
(b) Disconnect multi-functional instrument wire harness connector IP03.
(c) Use multimeter to measure test circuit.
Test Terminal
Conditions
Specified Value
IP03(4)——effective
grounding
Passenger Side Not Occupied
and Seat Belt Not Fastened
Less than 1 Ω
IP03(4)——effective
grounding
Passenger Side Not Occupied
and Seat Belt Fastened
10 kΩ or higher
Confirm if the resistance conforms to standard value.
Yes
The system is normal.
No
Yes
Go to step 5
No
Yes
The system is normal.
No
2588
6 Repair
the
circuit.
(a) Inspect and repair circuit fault points.
Confirm whether the alarm lamp displays normally if the multifunctional instrument
passenger-side safety belt is not worn.
7
Inspect the multifunctional instrument power and ground lines.
(a) Refer to the diagnosis
Confirm whether the alarm lamp displays normally if the multifunctional instrument
passenger-side safety belt is not worn.
8 Replace
function
instrument
(a) Refer to 11.13.8.1 Replacement of multi-functional instrument.
Confirm the completion of repair.
9
The system is normal.
Next
Yes
The system is normal.
No
Yes
The system is normal.
No
Yes
Go to step 7
No
2589
11.14.8 Removal and installation
11.14.8.1 Multi-function instrument replacement
Dismantlement procedure
Warning!
Warning: refer to warning on battery
disconnection in warnings and
precautions.
1. Disconnect the battery negative
cable. Refer to 2.11.8.1 battery
cable disconnection/connection
procedures.
2. For dismantling of central vent
port, refer to 8.2.8.18
Replacement of vent port of
instrument panel.
NL11-0121b
3. Dismantle fixing screw of
multi-functional instrument.
4. Disconnect
multi-functional
instrument wire harness
connector.
NL11-0122b
Installation procedure:
1. Connect to multi-function
instrument harness connector
NL11-0122b
2590
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст