Geely Emgrand X7. Manual part — 288
Geely Emgrand X7. Manual part - 288
27. Install synchronizer sleeve.
28. Install synchronizer spring.
29. Install synchronizer ring.
30. Install reverse gear.
31. Install needle bearing.
32. Install reverse gear sleeve.
套筒
倒档齿轮
GC03-0094b
33. Install needle bearing.
球轴承
GC03-0095b
34. Insatll spring snap ring.
Note: select and install spring snap ring to make
axial clearance of output shaft rear bearing
conform to standard value.
Standard value: -0.01~0.09mm
弹簧卡环
GC03-0096b
sleeve
Reverse gear
Ball bearing
Spring snap ring
1151
3.3.6.7 Reverse intermediate gear disassembly and assembly
Dismantle procedure
1. Dismantle spring snap ring 1.
2. Dismantle thrust washer 2.
3. Dismantle reverse intermediate gear 3 .
4. Dismantle needle bearing 4.
5. Dismantle Reverse intermediate gear shaft 5.
1
4
2
3
5
GC03-0097b
Installation procedure:
1. Install reverse intermediate gear shaft.
2. Install
needle
bearing.
3. Install reverse intermediate gear 3.
4. Install
thrust
washer.
5. Insatll spring snap ring.
1152
3.3.6.8 Disassemble and assemble of shift control mechanism
Dismantle procedure
1. Dismantle
bolt1.
2. Dismantle spring washer 2.
3. Dismantle the pin 3.
4. Dismantle return spring 4.
5. Dismantle limiting plate 5.
6. Dismantle limiter bracket 6.
7. Dismantle interlocking plate 7.
1
4
2
3
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
18
GC03-0009c
8. Dismantle
lockpin
8.
9. Dismantle control claw 9.
10. Dismantle limiter body 10.
11. Dismantle neutral gear return spring 11.
12. Dismantle neutral gear return spring seat 12.
13. Dismantle controller housing 13.
14. Dismantle needle bearing14.
15. Dismantle oil seal 15.
16. Dismantle control shaft cover 16.
17. Dismantle control shaft component 17.
18. Dismantle vent pipe 18.
Installation procedure::
锁销
控制指
GC03-0099b
1. Install aeration pope.
2. Install control shaft component.
3. Install control shaft cover.
4. Install the oil seal.
涂抹齿轮油
GC03-0100b
Lock pin
Control
thumbwheels
Coating gear oil
1153
5. Install
needle
bearing.
控制器壳
型号刻印
滚针轴承
的面
GC03-0101b
6. Install the controller housing.
7. Install the neutral gear return spring seat.
8. Install
the
neutral
gear return spring.
9. Install the limiter body.
10. Install the control claw.
11. Install lockpin.
控制器壳
型号刻印
滚针轴承
的面
GC03-0101b
12. Install interlocking plate.
13. Install limiter bracket.
14. Install limiting plate.
15. Install return spring.
16. Install the pin.
17. Install spring washer.
18. Install the bolt.
Controller housing
Model stamp
surface
Needle roller
bearing
Controller
housing
Model stamp
surface
Needle roller
bearing
1154
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст