Geely Emgrand X7. Manual part — 477
Geely Emgrand X7. Manual part - 477
10.2.4.6 DTC B1207 B1208
Fault diagnosis code Descriptions
B1207
Left front/left rear steering lamp with an open circuit
B1208
Left front/ left rear steering lamp short circuit to grounding fault
Circuit diagram:
NL11-3210b
6 SO31
3 SO31
8 CA12
8 IP48
9 IP48
5 CA12
8 CA18
5 CA18
6 SO24
3 SO24
左后组合灯
(左转向灯)
左前组合大灯
(左转向灯)
右前组合大灯
(右转向灯)
右后组合灯
(右转向灯)
BCM
TURN-LH LAMP
TURN-RH LAMP
Diagnostic Steps:
1
Check any fault code except forB1207 B1208
(a) Check if any fault code exist except for B1207 B1208
2
Measure left steering lamp voltage.
Yes
Go to
(DTC) list in 10.2.4.2
and repair according
to trouble codes.
No
Left rear
combinati
on lamp
(left
steering
lamp)
Left front
combination
headlamp
(left steering
lamp)
Right front
combinati
on
headlamp
(Right
steering
lamp)
Right
rearcombina
tion lamp
(Right
steering
lamp)
1907
(a) Turn the ignition switch to ON position.
(b) Turn on the left steering lamp.
(c) Measure voltage value of left front steering lamp
harness connector CA12 terminal8, left rear
steering lamp harness connector SO31 terminal6.
Standard Voltage: 11-14 V
Confirm if the voltage conforms to standard value.
9
6
5
1
2
3
4
7
8
1
2
3
4
5
6
CA12左前组合灯线束连接器
IP48BCM线束连接器
SO31左后组合灯线束连接器
NL11-3212b
1 2 3
4 5 6
7 8 9
10 11 12 13
3
Inspect the bulb.
(a) Check if the bulb of turning light is blown.
Confirm whether the license plate lamp bulb is blown out.
4
Inspect the communication among the BCM, the left front steering lamp and the left rear steering
lamp.
No
Go to step 4
Yes
Yes
Replace the bulb .
No
IP48BCMharness connector
CA12 left front combination lamp harness connector
SO31 left rear combination lamp harness connector
1908
(a) Turn the ignition switch to OFF position.
(b) Disconnect BCM harness connector IP48.
(c) Disconnect the steering lamp harness connector
CA12、SO31.
(d) Measure resistance between BCM wire harness
connector IP48 terminal 8 and license lamp wire
harness connector CA12 terminal 5.
(e) Measure resistance between BCM wire harness
connector IP48 terminal 8 and license lamp wire
harness connector SO31 terminal 3.
Standard Resistance: Less than 1 Ω
Confirm if the resistance conforms to standard value.
9
6
5
1
2
3
4
7
8
1
2
3
4
5
6
CA12左前组合灯线束连接器
IP48BCM线束连接器
SO31左后组合灯线束连接器
NL11-3212b
1 2 3
4 5 6
7 8 9
10 11 12 13
5
Inspect the communication among the left front steering lamp, the left
rear steering lamp and grounding.
No
Repair or replace the harness.
Yes
IP48BCMharness connector
CA12 left frontcombination lamp harness connector
SO31 left rear combination lamp harness connector
1909
(a) Disconnect steering lamp harness
connector CA12, SO31.
(d) Measure the resistance between
terminal 8 of license lamp harness
connector CA12 and grounding.
(c) Measure resistance value between
license lamp harness connector
SO31 terminal6 and grounding.
Standard Resistance: Less than 1 Ω
(d) Measure the resistance between
terminal 5 of license lamp harness
connector CA12 and grounding.
(e) Measure resistance value between
license lamp harness connector
SO31 terminal3 and grounding.
Standard Resistance: More than 10 Ω or
higher
Confirm if the resistance conforms to
standard value.
9
6
5
1
2
3
4
7
8
1
2
3
4
5
6
CA12左前组合灯线束连接器
SO31左后组合灯线束连接器
NL11-3213b
6
Replace the BCM
(a) Replace BCM and refer to
Replacement of BCM in 11.8.8.1
.
Confirm the completion of repair.
7
The system is normal.
No
Repair or replace the harness.
Yes
Next
CA12 left front combination lamp harness connector
SO31 leftrear combination lamp harness connector
1910
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст